Bosch Logamatic EMS RC35 Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 64

background image

Logamatic EMS – 6 720 801 387 (2011/05)

7

Product information

2

2

Product information

2.1

Correct use

The RC35 programming unit must only be used to operate and control Buderus heating systems in
detached houses and residential buildings.

B

Always use this appliance correctly and in conjunction with the specified control systems.

B

Observe all regulations and standards applicable to the installation and operation of the system
in your country!

The boiler must be equipped with EMS (Energy Management System) or UBA1.x (Universal Burner
Automation).

Do not operate the programming unit with controllers of the Logamatic 2000/4000 control systems.
We recommend that you always operate the heating system with a programming unit (without a
programming unit only emergency mode is possible).
If RC2xremote programmers are used, which were manufactured up to and including 2005, only two
remote programmers can be connected. In case of related questions, please contact your local
Buderus sales office.

These instructions describe all possible functions of the RC35 programming unit. Some of these
functions may not be available, depending on which boiler (combustion controller) is used. You will
find information on this in the relevant chapter.
For information regarding the combustion controller, see menu

DIAGNOSIS\VERSIONS

(

Æ

page 50).

RC35 as replacement for ERC

If the RC35 programming unit is used as a replacement for the ERC controller, there are differences
for example as regards the basic settings. For an overview of these, see Tab. 4, page 10.

2.2

EU Declaration of Conformity

The design and operation of this product conform to the European Directives and the supplementary
national requirements. Its conformity is demonstrated by the CE designation. You can call up the
Declaration of Conformity for this product on the internet at www.buderus.de/konfo or request a
copy from your local Buderus sales office.

2.3

Included in Delivery

• RC35 programming unit

• Operating instructions

• Installation and maintenance instructions

• Wall mounting base, fixing material

«
...
5
6
7
8
9
...
»

Содержание Logamatic EMS RC35

































































Отзывы:

Нет отзывов

Похожие инструкции для Logamatic EMS RC35

FPBA-01 PROFIBUS DP

Бренд: ABB Страницы: 2

ControlMaster CM15

Бренд: ABB Страницы: 4

Бренд: Baccara Страницы: 16

Бренд: BABYSTYLE Страницы: 8

Бренд: BABYSTYLE Страницы: 32

Бренд: Jäger Страницы: 50

Бренд: V2 Страницы: 12

Бренд: H3C Страницы: 5

NORA-W10 Series

Бренд: u-blox Страницы: 56

Бренд: z21 Страницы: 2

Бренд: Full Gauge Controls Страницы: 3

Бренд: Absima Страницы: 5

Бренд: Osram Страницы: 3

Бренд: OJ Electronics Страницы: 8

Бренд: National Instruments Страницы: 14

Бренд: nvent Страницы: 4

Бренд: Wenglor Страницы: 44

Бренд: YASKAWA Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды