Bosch Logamatic EMS RC35 Скачать руководство пользователя страница 52

Страница: 52 / 64

Reset

Logamatic EMS – 6 720 801 387 (2011/05)

Reset

The

RESET

menu allows you to reset

• all parameters to basic setting

• the fault list

• the service message

and

• the hours run

Turn the rotary selector

to select a menu, e.g

error list.

Press buttons

to switch into the display, e.g

Would you like to reset the error list?

Press buttons

and turn rotary switch

to set the display to

Yes.

The reset is implemented after you release the button.
An appropriate message is shown during the reset; this will close automatically

Once reset is complete: confirm the new message by pressing any key.

1) With boilers with UBA1.x, DBA or UBA-H3 only all the parameters of the RC35 are reset, but not the

parameters of the automatic firing units of.

2) This function is not possible with boilers with UBA1.x or DBA

After resetting to the basic position, you must reset the parameters according to the
system configuration.

Содержание Logamatic EMS RC35

































































Результаты поиска

Содержание Logamatic EMS RC35

Отзывы:

Похожие инструкции для Logamatic EMS RC35

Бренды по названию

Популярные бренды

Bosch Logamatic EMS RC35, Инструкция по установке и обслуживанию

Результаты поиска

Содержание Logamatic EMS RC35

Отзывы:

Похожие инструкции для Logamatic EMS RC35

Бренды по названию

Популярные бренды