Bosch Logamatic EMS RC35 Скачать руководство пользователя страница 43

Страница: 43 / 64

Logamatic EMS – 6 720 801 387 (2011/05)

System settings (Service menu – Settings)

6.6

Solar data

Turn the

rotary selector to the left until

solar data

is selected.

Press

to select

solar data

SETTINGS\SOLAR

opens.

Menu item

Input range

Standard setting

Other
information

What is the max. stor.
cylinder temp. of the solar
system?

30 °C to 90 °C

60 °C

1) Not possible or not available with boilers with UBA1.x or DBA.

Below which temperature
should the cylinder not fall?

30 °C to 54 °C, off

OFF

What is the minimum pump
rating?

20 % to 100 %

100 %

Table 17 Navigator for service menu\Settings\Solar data

For explanations of the settings, see the documentation for the solar module.

boiler data
domestic hot water
heating circuit 1
solar data

SERVICE\SETTINGS

Содержание Logamatic EMS RC35

































































Результаты поиска

Содержание Logamatic EMS RC35

Отзывы:

Похожие инструкции для Logamatic EMS RC35

Бренды по названию

Популярные бренды

Bosch Logamatic EMS RC35, Инструкция по установке и обслуживанию

Результаты поиска

Содержание Logamatic EMS RC35

Отзывы:

Похожие инструкции для Logamatic EMS RC35

Бренды по названию

Популярные бренды