Bosch CLC6001i 25 E Скачать руководство пользователя

Страница: 15 / 120

3-1

Climate Class 6100i / 6000i / 8100i / 8000i

CHAPTER 3.

FUNCTION

[1] FUNCTION

1 Restart control

Once the compressor stops operating, it will not restart for 180 sec-

onds to protect the compressor.
Therefore, if the operating compressor is shut down from the remote

control and then turned back on immediately after, the compressor

will restart after a preset delay time.
(The indoor unit will restart operation immediately after the ON

switch is operated on the remote control.)

2. Indoor unit heat exchanger freeze prevention

control

If the temperature of the indoor unit heat exchanger remains below

0°C for 4 consecutive minutes during cooling or dehumidifying oper-

ation, the compressor operation stops temporarily in order to prevent

freezing. When the temperature of the indoor unit heat exchanger

rises to 2°C or higher after about 180 seconds, the compressor re-

starts and resumes normal operation.

3. Outdoor unit overheat prevention control

During cooling operation, if the temperature of the outdoor unit

heat exchanger exceeds the outdoor unit heat exchanger overheat

prevention temperature (about 55°C), the operating frequency is de-

creased by about 4 to 15 Hz.
Then, this operation is repeated every 60 seconds until the tem-

perature of the outdoor unit heat exchanger drops to about 54°C

or lower. Once the temperature of the outdoor unit heat exchanger

drops to about 54°C or lower, the operating frequency is increased

by about 4 to 10 Hz every 60 seconds until the normal operation

condition resumes. If the temperature of the outdoor unit heat ex-

changer exceeds the outdoor unit heat exchanger overheat protec-

tion temperature for (120 sec : outdoor temperature ≥ 40°C • 60 sec

: outdoor temperature < 40°C) at minimum operating frequency, the

compressor stops operating and then restarts after about 180 sec-

onds, and the above mentioned control is repeated.

4. Compressor overheat prevention control

If the temperature of the compressor exceeds the compressor over-

heat prevention temperature (110°C), the operation frequency is

decreased by about 4 to 10 Hz.
Then, this operation is repeated every 60 seconds until the tempera-

ture of the compressor drops below the overheat protection tem-

perature (110°C). Once the temperature of the compressor drops

below the overheat protection temperature, the operating frequency

is increased by about 4 to 10 Hz every 60 seconds until the normal

operation condition resumes. If the temperature of the compressor

exceeds the overheat protection temperature for a certain time (120

sec : outdoor temperature ≥ 40°C • 60 sec : outdoor temperature <

40°C) at minimum operating frequency, the compressor stops op-

erating and then restarts after about 180 seconds, and the above

control is repeated.

5. Startup control

6. Outdoor unit fan delay control

The compressor stops immediately after cooling or dehumidifying or

heating operation is shut down, but the outdoor unit fan continues

operation for 50 seconds.

7 ON timer

The ON timer can be activated by pressing the ON timer button.

When the ON timer is activated, the operation start time is adjusted

based on fuzzy logic calculations 2 hour before the set time so that

the room temperature reaches the set temperature at the set time.

8. OFF timer

The OFF timer can be activated by pressing the OFF timer button.

When the OFF timer is activated, the internal timer start to count

down the remaining time from set time. And the unit will turn off au-

tomatically when it reach to zero.

9. Power ON start

If the connecting wire HAJP is put on the PWB assembly, when the

power is supplied by turning on a circuit breaker, the air conditioner

automatically starts of operation in “AUTO”. (Refer to Indoor side

PWB).

10. AUTO MODE

1) AUTO mode of remote control

(only for CLC6101i-W 50/65 HE model)

AUTO mode of AUX button

(for all models)

In the AUTO mode, the temperature setting and mode are automat-

ically selected according to the room temperature and outdoor tem-

perature when the unit is turned on.

Modes and Temperature Settings

the figures in ( ) are temperature settings

During operation, if the outdoor temperature changes, the tempera-

ture settings will automatically slide as shown in the chart.

2) AUTO mode of remote control

(only for CLC6001i-W 25/35 E model)

n the AUTO mode, the unit selects operating mode (Heating/Cool-

ing) according to temperature setting which set by user and room

temperature.

11. Auto restart

When power failure occurs during operation, the unit will automati-

cally restart in the same setting which were active before the power

failure.

1) Setting memorized

• Operating mode (Heat, Cool, Dry, PCI)
• Temperature adjustment (within 2

℃

range) automatic operation.

• Temperature setting
• Fan setting
• Air flow direction
• Power ON/OFF
• Automatic operation mode setting
• Plasmacluster mode
• OD SILENT setting
• SPOT setting

2) Setting not memorized

• Timer setting

Содержание CLC6001i 25 E

























































































































Результаты поиска

Содержание CLC6001i 25 E

Отзывы:

Похожие инструкции для CLC6001i 25 E

Бренды по названию

Популярные бренды

Bosch CLC6001i 25 E, Руководство по обслуживанию

Результаты поиска

Содержание CLC6001i 25 E

Отзывы:

Похожие инструкции для CLC6001i 25 E

Бренды по названию

Популярные бренды