Bosch CLC6001i 25 E Скачать руководство пользователя

Страница: 40 / 120

4-20

Climate Class 6100i / 6000i / 8100i / 8000i

Problem

symptom

Outdoor

unit

indica-

tion

(LED1)

Malfunction

No.*

Content of diagnosis

Check point

Action

Main

Sub

Main

Sub

Indoor unit

operates.

Outdoor

unit

does not

operate.

Lighting

OFF

Wiring

between

units

Serial opencircuit 1) Check the wires between

units.

1) Connect stable power

supply. Correct the

wiring.

2) Check voltage between

N and 1 the indoor/out-

door unit terminal boards.

2) Replace the outdoor

unit control PWB as-

sembly.

3) Check the outdoor unit

fuse.

3) Replace the fuse/ out-

door unit control PWB

assembly.

4) Check voltages of

15V-0V,12V-0V and 5V-

0V on the PWB.

15V-0V :15V

12V-0V :12V

5V-0V :5V

Check resistance be-

tween IPM terminals.

4) Replace the outdoor

unit control PWB as-

sembly.

5) No abnormality found

in above inspections (1)

through (4).

5) Replace the outdoor

unit control PWB board.

Indoor unit

operates.

Outdoor

unit

does not

operate.

Lighting

OFF

Wiring

between

units

Serial short-cir-

cuit

1) Check the wiring be-

tween units.

1) Correct the wiring.

Indoor and

outdoor

units

do not

operate.

Serial erroneous

wiring

1) Check the wiring be-

tween units.

1) Correct the wiring.

Indoor and

outdoor

units do

not

operate.

Normal

blinking

OFF

Indoor unit

fan

Indoor unit fan

error

1) Check the indoor fan

motor for proper rotating

operation. (Check fan

lock.)

1) Replace the indoor fan

motor.

2) Check the lead wire of

the indoor fan motor for

open-circuit.

2) Replace the indoor fan

motor.

3) Check connector of the

indoor unit fan motor for

secure installation

3) Correct the installation

of the indoor fan motor

connector.

4) No abnormality found

in above inspections (1)

through (3).

4) Replace the indoorunit

control PWB

Indoor and

outdoor

units do

not

operate.

Normal

blinking

or OFF

Indoor unit

control PWB

EEPROM data

error

1) (EEPROM read data

error)

1) Replace the indoor unit

control PWB

Содержание CLC6001i 25 E

























































































































Результаты поиска

Содержание CLC6001i 25 E

Отзывы:

Похожие инструкции для CLC6001i 25 E

Бренды по названию

Популярные бренды

Bosch CLC6001i 25 E, Руководство по обслуживанию

Результаты поиска

Содержание CLC6001i 25 E

Отзывы:

Похожие инструкции для CLC6001i 25 E

Бренды по названию

Популярные бренды