Bosch CLC6001i 25 E Скачать руководство пользователя | Manualshive

Страница: 26 / 120

background image

4-6

Climate Class 6100i / 6000i / 8100i / 8000i

[4] HOW TO OPERATE THE OUTDOOR UNIT INDEPENDENTLY

1.Cooling in 40 Hz fixed mode

To operate the outdoor unit independently, short-circuit the sections indicated by arrows in the diagram below with an adapter, and apply 230 VAC

between (1) and (N) on the terminal board of the outdoor unit. This allows the outdoor unit to be operated in cooling mode independently.
(Do not operate the outdoor unit in this condition for an extended period of time.)

L3

L2

If these pads are connected and Power is applied to N and 1 on terminal board.

Then the outdoor unit operate in "TEST COOL 40Hz" mode.

Soldering Side

C5

C6

[5] GENERAL TROUBLESHOOTING CHART

* These models have following thermistors

INDOOR UNIT

OUTDOOR UNIT

TH1, TH2

TH1, TH2, TH3, TH4, TH5

The errors for the thermistors that are not mentioned above are irrelevant.
These indoor units don’t have power relay.

1.Indoor unit does not turn on

Main cause

Inspection method

Normal value/condition

Remedy

Cracked PWB.

(Cracked pattern)

Check visually.

There should be no cracking in

PWB or pattern.

Replace PWB.

Open-circuit in FU1

(250 V, 3.15 A)

Check melting of FU1.

There should be no open-cir-

cuit.

Replace PWB.

2.Indoor unit fan does not operate

Main cause

Inspection method

Normal value/condition

Remedy

Open-circuit in heat exchanger

thermistor (TH2) (in heating opera-

tion)

Measure thermistor resistance

(dismount for check).

Refer to THERMISTOR TEM-

PERATURE CHARACTERIS-

TICS-1

Replace thermistor.

There should be no open-cir-

cuit or faulty contact.

Replace thermistor.

Disconnected heat exchanger therm-

istor (TH2) (in heating operation)

Inspect connector on PWB.

Check thermistor installation

condition.

Thermistor should not be dis-

connected.

Install correctly.

3.Indoor unit fan speed does not change

Main cause

Inspection method

Normal value/condition

Remedy

Remote control not designed to allow

fan speed change.

Check operation mode.

Fan speed should change

except during dehumidifying

operation, ventilation, light de-

humidifying operation, internal-

ly normal operation

Explain to user.

4.Remote control signal is not received

Main cause

Inspection method

Normal value/condition

Remedy

Batteries at end of service life.

Measure battery voltage.

2.5 V or higher (two batteries in

series connection)

Install new batteries.

Batteries installed incorrectly.

Check battery direction.

As indicated on battery com-

partment.

Install batteries in indicated

direction.

Lighting fixture is too close, or fluo

-

rescent lamp is burning out.

Turn off light and check.

Signal should be received

when light is turned off.

Change light position or install

new fluorescent lamp.

«
...
24
25
26
27
28
...
»

Содержание CLC6001i 25 E

























































































































Отзывы:

Нет отзывов

Похожие инструкции для CLC6001i 25 E

Бренд: Waterous Страницы: 13

Бренд: Waterous Страницы: 8

Бренд: Daikin Страницы: 52

Бренд: Daikin Страницы: 147

Бренд: Daikin Страницы: 175

Бренд: JBL Страницы: 12

Бренд: Lasko Страницы: 4

Бренд: Lasko Страницы: 4

Бренд: Lasko Страницы: 4

Бренд: Lasko Страницы: 4

Бренд: Lasko Страницы: 4

Бренд: Lasko Страницы: 4

Бренд: Lasko Страницы: 4

Бренд: Powerhorse Страницы: 48

Бренд: T.I.P. Страницы: 104

Бренд: Watson-Marlow Страницы: 576

Бренд: Warm Tech Страницы: 61

Бренд: KEKAI Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды