Bosch CLC6001i 25 E Скачать руководство пользователя

Страница: 30 / 120

4-10

Climate Class 6100i / 6000i / 8100i / 8000i

6.Motion sensor trouble-shooting

! CAUTION !

• Sometimes, the buzzer sound is not stable for 3 minutes at just after pluging the power supply.

• Sometimes, the buzzer sound lags behind movement.

Press the AUX bu

on.

The air condi

oner starts opera

on.

Press the display bu

on on the remote controller

and check opera

onLED lamp get dark.

The buzzer sounds if

someone move in

front of the sensor.

The Buzzer doesn't

sound if anyone

don't move in front

of the sensor.

YES

OK.

Swap the Mo

on Sensor Board.

YES

OK.

er that Press the AUX bu

on for 5 seconds.

Check Opera

on LED lamps is blinking.

Have the

problem been

ﬁ

xed?

Swap the Display Board.

Have the

problem been

ﬁ

xed?

Swap the Control Board.

YES

OK.

Содержание CLC6001i 25 E

























































































































Результаты поиска

Содержание CLC6001i 25 E

Отзывы:

Похожие инструкции для CLC6001i 25 E

Бренды по названию

Популярные бренды

Bosch CLC6001i 25 E, Руководство по обслуживанию

Результаты поиска

Содержание CLC6001i 25 E

Отзывы:

Похожие инструкции для CLC6001i 25 E

Бренды по названию

Популярные бренды