Bosch CLC6001i 25 E Скачать руководство пользователя | Manualshive

Страница: 19 / 120

background image

3-5

Climate Class 6100i / 6000i / 8100i / 8000i

[3] IPM Drive Circuit

The IPM is used for compressor drive. The power supply for the IPM drive, the shunt resistance for over current detection, etc., are provided outside

the IPM (control PWB).

1. IPM drive power supply circuit

The power supply for the upper-phase IGBT (HU, HV, HW) drive employs a bootstrap system, and provides power to the upper-phase IC.
The 15-V power supply for the lower-phase IC is provided by the control printed wiring board (PWB).

1.1. Brief explanation of bootstrap system (single power drive system)

To supply power to the upper-phase IC, the microcomputer (IC1) turns ON the lower-phase IGBT (LU, LV, LW).

This results in a charging current that flows to the electrolytic capacitor of each upper-phase IC input and charges the bootstrap capacitor with a 15V

current.
The power supply for the subsequent stages is charged while the lower-phase IGBT is ON in ordinary compressor drive control.

1.2 DC over current detection circuit

When a current of about 20 A or higher flows through the shunt resistance on the control printed wiring board (PWB), the voltage at this resistance

is input to IPM CIN pin (15). Then, the gate voltage of the lower-phase IGBT (LU, LV, LW) inside the IPM turns OFF to cut off the over current. At the

same time, an L output of more than 20μs is generated from IPM from pin (14), and this results in an L input to over current detection input pin (45)

of the microcomputer (IC1) and turns OFF the PWM signal output (IC1 pins (37) through (39) and pins (42) through (44)) to the IGBT gate.

«
...
17
18
19
20
21
...
»

Содержание CLC6001i 25 E

























































































































Отзывы:

Нет отзывов

Похожие инструкции для CLC6001i 25 E

Бренд: JBL Страницы: 12

Бренд: Mr. Heater Страницы: 28

Бренд: Wacker Neuson Страницы: 42

Бренд: T.I.P. Страницы: 134

HEATSTAR MH35CLP

Бренд: Mr. Heater Страницы: 32

Бренд: Wilden Страницы: 39

Life Smart Zone LCHT10955US

Бренд: Source Network Страницы: 16

Бренд: UNITED Страницы: 4

Бренд: samhydraulik Страницы: 14

TurboSilence InverX IXCR36

Бренд: Fairland Страницы: 117

Бренд: Crane Страницы: 11

Бренд: Homa Страницы: 40

Бренд: MONDEX Страницы: 16

Бренд: Oceanic Страницы: 29

Бренд: ASP Страницы: 5

Бренд: Almost Heaven Saunas Страницы: 8

Бренд: FLORABEST Страницы: 94

Бренд: Waspper Страницы: 11

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды