Bosch B8512G Скачать руководство пользователя страница 35 | Manualshive

Страница: 35 / 284

background image

Control Panel

Panel Wide Parameters | en

35

Bosch Security Systems, Inc.

Program Entry Guide

2017.03 | 09 | F.01U.303.998

Notice!
Limit unwanted traffic, choose a port number greater than 1023

In order reduce the risk of unwanted network traffic interfering with control panel IP
communications, select a port number above 1023.

RPS Menu Location

Panel Wide Parameters > Onboard Ethernet Communicator > TCP/UDP Port Number

3.2.12

TCP Keep Alive Time (sec.)

Default

: 45

Selections

: 0 - 65 (seconds)

This parameter sets the time in seconds between TCP keep-alive transmissions to verify that
an idle connection is still active.

RPS Menu Locations

Panel Wide Parameters > Onboard Ethernet Communicator > TCP Keep Alive Time (sec.)

3.2.13

IPv4 Test Address

Default

: 8.8.8.8

Selections

: IPv4 address or Domain Name

The default test address works for most networks.
The control panel uses the IP communicator to ping the IPv4 Test Address to verify the
integrity of the network and the network configuration settings.

Further information

IP Address and Domain Name formats, page 282

RPS Menu Locations

Panel Wide Parameters > Onboard Ethernet Communicator > IPv4 Test Address

3.2.14

IPv6 Test Address

Default

: 2001:4860:4860::8888

Selections

: IPv6 address or Domain Name

The default test address works for most networks.
This parameter is only available when IPv6 Mode is set to Yes.
The control panel uses the IP communicator to ping the IPv4 Test Address to verify the
integrity of the network and the network configuration settings.

Further information

IP Address and Domain Name formats, page 282

RPS Menu Location

Panel Wide Parameters > Onboard Ethernet Communicator > IPv6 Test Address.

3.2.15

Alternate IPv4 DNS server IP address

Default

: 0.0.0.0

Selections

: 0.0.0.0 to 255.255.255.255

This parameter provides an alternate IPv4 DNS server IP address.
If the IP communicator fails to obtain an address from the primary server, it tries the alternate
DNS server.

Further information

IP Address and Domain Name formats, page 282

RPS Menu Locations

Panel Wide Parameters > Onboard Ethernet Communicator > Alternate IPv4 DNS server
IP address

«
...
33
34
35
36
37
...
»

Содержание B8512G





























































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для B8512G

Бренд: Eaton Страницы: 28

Бренд: Parallel Страницы: 16

Бренд: V2 Страницы: 46

Бренд: Zeta Страницы: 44

Бренд: Partizan Страницы: 7

Бренд: Measurement Computing Страницы: 32

Бренд: Nemesis Страницы: 6

Бренд: Allen-Bradley Страницы: 16

Бренд: D+H Страницы: 2

Бренд: Jeckson Electric Страницы: 2

Бренд: Estun Страницы: 41

Elan SRB 201ZH X3

Бренд: schmersal Страницы: 6

Бренд: Samson Страницы: 44

Бренд: Hansen Страницы: 12

NETBuilder II DPE 80

Бренд: 3Com Страницы: 32

Бренд: 4IPNET Страницы: 11

Бренд: KAR-TECH Страницы: 55

10 AMP RVC-MPPT

Бренд: Go Power Страницы: 17

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды