Bosch B8512G Скачать руководство пользователя страница 31 | Manualshive

Страница: 31 / 284

background image

Control Panel

Panel Wide Parameters | en

31

Bosch Security Systems, Inc.

Program Entry Guide

2017.03 | 09 | F.01U.303.998

Selections

:

–

Yes - Send expanded test reports.

–

No - Do not send expanded test reports.

When this parameter is set to Yes, the control panel expands test reports to include off-normal
system status information.
The control panel expands manually initiated test reports and Sked initiated (scheduled) test
reports.

RPS Menu Location

Panel Wide Parameters > Phone and Phone Parameters > Expand Test Report

3.1.9

PSTN Compatibility

Default

: USA

Selections

:

–

USA

–

Australia

–

New Zealand

This parameter configures the control panel and the B430 Plug-in Telephone Communicator to
support public switched telephone networks (PSTN) in the USA, Australia, or New Zealand.

Notice!
PSTN requirement for Australia / New Zealand, disable RPS answer armed/disarmed

If you set this PSTN Compatibility parameter to Australia or New Zealand, you must set
Panel Wide Parameters > RPS Parameters > Answer Armed and Answer Disarmed to 0
(disabled).

RPS Menu Location

Panel Wide Parameters > Phone and Phone Parameters > PSTN Compatibility

3.2

On Board Ethernet (IP) Communicator

3.2.1

IPv6 Mode

Default

: No

Selections

:

–

Yes - Enable IPv6

–

No - Disable IPv6 (Use IPv4 mode).

This parameter configures IP communication for IPv6 (Internet Protocol version 6) or IPv4
(Internet Protocol version 4)
When IPv6 Enable is set to Yes, the IPv4 parameters are read only (grayed out and not
editable). Set DHCP/AutoIP enable to Yes.
When IPv6 Enable is set to No, the IPv6 parameters are read only (grayed out and not
editable).

RPS Menu Locations

Panel Wide Parameters > Onboard Ethernet Communicator > IPv6 Mode,

3.2.2

IPv4 DHCP/AutoIP Enable

Default

: Yes

Selections

:

–

Yes - enable DHCP to automatically configure the IP Address, IP Default Gateway, and IP
DNS Server Address.

–

No - manually configure the IP Address, IP Default Gateway, and IP DNS Server Address.
Use this setting if there is no DHCP service.

«
...
29
30
31
32
33
...
»

Содержание B8512G





























































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для B8512G

Бренд: Farris Engineering Страницы: 12

Бренд: Eastern Times Technology Страницы: 4

Бренд: Vacon Страницы: 18

Бренд: Warren Controls Страницы: 16

Бренд: Mackie Страницы: 16

Бренд: TANDBERG Страницы: 47

Бренд: Hattersley Страницы: 2

Бренд: National Instruments Страницы: 6

Micro850 series

Бренд: Allen-Bradley Страницы: 24

Бренд: Hearth Products Controls Страницы: 5

Бренд: M-system Страницы: 5

Бренд: Satel Страницы: 7

Бренд: IFM Страницы: 41

Бренд: Duco Страницы: 16

Бренд: Allen-Bradley Страницы: 88

Бренд: Grundfos Страницы: 12

TotalArc BMS 460346 SOLAR POWER

Бренд: OGI Страницы: 28

Бренд: Niko Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды