Body Solid G5S Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 39

Body Solid G5S Скачать руководство пользователя страница 8

4

Be careful to assemble all components
in the sequence they are presented.

mm

Inch

A.

Attach two Convex End Caps (3) to the top of Seated Press Arm Support (N).

Attach Seated Press Arm Support (N) to Top Frame (F) using Shaft (73), and tighten

Allen Screw (66).

B.

Attach Seated Press Arm (P) to Seated Press Arm Support (N) using Shaft (74), and tighten

Allen Screw (66).

Attach two 1” X 2” Convex End Caps (6) to the top of the Seated Press Arm (P).

C.

Attach two Seated Press Handles (Q) to Seated Press Arm (P) using:

Six 62 (3/8” x 5/8” flat allen head bolt)

Six 92 (3/8” bent lock washer)

Foam Grip (83) and Round End Cap (16) are preinstalled.

D.

Attach Foot Plate (R) to Adjustable Chrome Frame (S) with Shaft (76) and tighten Allen Screw (27).

E.

Slide Adjustable Chrome Frame (S) into Main Base Frame (A) and hold in place with T-Shaped

Pop Pin (26).

Slide two Round End Caps (7) into the openings on the top of the Adjustable Chrome Frame (S)

as shown.

8

NOTE:

Finger tighten all hardware in this step. Do Not wrench tighten until end of step 7.

S T E P

«
...
6
7
8
9
10
...
»

Содержание G5S








































Отзывы:

Нет отзывов