manualshive.com logo in svg

Body Solid G5S, Руководство по сборке, Страница: 32 / 39

Поделиться
Скачать
Body Solid G5S Скачать руководство пользователя страница 32

Be careful to assemble all components
in the sequence they are presented.

mm

Inch

SEE NOTE 1 ON PAGE 41:

A.

Apply weight stack numbers to weight stack Top Plate (8) and each Weight Stack Plate 

as shown. 

SEE NOTE 2 ON PAGE 41:

B.

Weight Stack Shroud (BA) is pre-assembled with Shroud Insert (BB).

Attach Weight Stack Shroud (BA) to the side of the weight stack as shown.

Bolt onto Main Base Frame (A) at the bottom and Top Weight Stack Frame (AB) using:

Two 62 (3/8” x 5/8” round allen head)

Two 58 (3/8” washer)

C.

Attach Back Weight Stack Shroud (BC), to the back side of the weight stack, onto the Main Base 

Frame (A) at the bottom and to the Top Weight Stack Frame (AB) as shown using:

Two 62 (3/8” x 5/8” round allen head)

Two 58 (3/8” washer)

D.

Attach Press Arm Shroud (BD) to the Seated Press Arm Support (N) using:

Four 68 (1/8” x 5/8” round allen head)

E.

Connect the Water Bottle Bracket (102) to the Weight Stack Shroud (BA) using:

Two 103 (1/8” x 3/8” screw)

F.

Slide the Water Bottle Holder (101) onto the Water Bottle Bracket (102) as shown.

32

16

S T E P

Содержание G5S








































Отзывы:

Нет отзывов