Body Solid G5S Скачать руководство пользователя страница 20 | Manualshive

Страница: 20 / 39

Body Solid G5S Скачать руководство пользователя страница 20

10

Be careful to assemble all components
in the sequence they are presented.

S T E P

mm

Inch

20

A.

See diagram 2. Attach Double Adjustable Pulley Holder (CA) to the small arm sticking out of the

Angled Support Frame (E) as shown using:

One 57 (1/2” washer)

One 55 (1/2” nylon lock nut)

B.

Install Pulley (A7) into Double Adjustable Pulley Holder (CA), install into the third hole from the

top, as shown in diagram 2 using:

One 49 (3/8” x 1 3/4” hex head bolt)*

Two 58 (3/8” washer)

One 56 (3/8” nylon lock nut)

See diagram 1. Route Cable (96) through Double Adjustable Pulley Holder (CA) and under
Pulley (A7).

*NOTE:
Leave Pulley (A7) finger tight, until after final cable adjustments in Step 15.

C.

See diagram 1. Route Cable (96) through the flange hanging from Top Frame (F) and hold in
place with Pulley (A8). Install Pulley (A8) as shown in diagram 2 using:

One 49 (3/8” x 1 3/4” hex head bolt)
Two 58 (3/8” washer)
One 56 (3/8” nylon lock nut)

D.

Route Cable (96) through the top of 45 Degree Double Pulley Holder (CB) and hold in place with
Pulley (A9) as shown in diagram 2 using:

One 49 (3/8” x 1 3/4” hex head bolt)

Two 58 (3/8” washer)

One 56 (3/8” nylon lock nut)

E.

See diagram 2. Install Pulley (A10) to the flange above the Top Weight Stack Frame (AB) using:

One 49 (3/8” x 1 3/4” hex head bolt)

Two 58 (3/8” washer)

One 56 (3/8” nylon lock nut)

F.

See diagram 1. Route Cable (96) up through the Top Weight Stack Frame (AB) above
Pulley (A10), and down through Top Weight Stack Frame (AB) toward weight stack.

G.

See diagram 1A. Remove Hex Head Bolt (38) from Selector Rod Top Bolt (37), slide Cable (96)
through Selector Rod Top Bolt (37) and out through the side. Attach Cable End Shaft (90) and
tighten Allen Screw (91). Pull Cable (96) tight, so Cable End Shaft (90) fits inside Selector Rod
Top Bolt (37). Reinstall Hex Head Bolt (38) in Selector Rod Top Bolt (37).

Ball Stop End

Metal Ball End

4955 mm

16’ 3”

Lat Pulldown Cable (96)

«
...
18
19
20
21
22
...
»

Содержание G5S








































Отзывы:

Нет отзывов