Body Solid G5S Скачать руководство пользователя страница 24 | Manualshive

Страница: 24 / 39

Body Solid G5S Скачать руководство пользователя страница 24

12

S T E P

Be careful to assemble all components
in the sequence they are presented.

Ball Stop End

Ball Stop End

5185mm

17’ 1”

Ab Crunch Cable (97)

mm

Inch

24

757mm

2’ 5”

Stamped Eye

Stamped Eye

Short Cable (99)

A.

See diagram 1. Route Cable (97) through Pulley Holder with Hook (CD) and hold Cable (97) in place

with Pulley (B4) as shown in diagram 2 using:

One 49 (3/8” x 1 3/4” hex head bolt)

Two 58 (3/8” washer)

One 56 (3/8” nylon lock nut)

NOTE:

If you are not installing the Leg Press, then connect Short Cable (99) to the bottom of

Pulley Holder With Hook (CD) and to Main Frame (A). See Cable 99 diagram .

B.

See diagram 1. Route Cable (97) through the bottom of the 45 Degree Double Pulley Holder (CB) and

hold Cable (97) in place with Pulley (B5) as shown in diagram 2 using:

One 49 (3/8” x 1 3/4” hex head bolt)

Two 58 (3/8” washer)

One 56 (3/8” nylon lock nut)

C.

See diagram 1. Route Cable (97) under Pulley (B6) -preinstalled. Route Cable (97) forward towards the

front of the gym.

Insert Cable (97) through small pillar in Main Frame (A), then through Angled Support Frame (E),

and under Pulley (B7) -preinstalled.

D.

See diagram 1. Route Cable (97) through pulley holder at the end of the Leg Extension Arm (Y).

Install Pulley (B8) as shown in diagram 2 using:

One 49 (3/8” x 1 3/4” hex head bolt)

Two 58 (3/8” washer)

One 56 (3/8” nylon lock nut)

Install hex head bolt (49) into the end of the Leg Extension Arm (Y) to hold Cable (97) in place as

shown in diagram 2.

«
...
22
23
24
25
26
...
»

Содержание G5S








































Отзывы:

Нет отзывов