Body Solid G5S Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 39

Body Solid G5S Скачать руководство пользователя страница 18

9

Be careful to assemble all components
in the sequence they are presented.

S T E P

mm

Inch

18

Lat Pulldown Cable (96)

Ball Stop End

Metal Ball End

4955 mm

16’ 3”

A.

See diagram 1. Begin at the high pulley station. Route the Lat Pulldown Cable (96) up through the first

opening where pulley (A1) will be installed, and out through the top. Route Cable (96) above the Top

Frame (F) and then down through the second opening where pulley (A2) will be installed. Pull the

entire length of cable through.

B.

See diagram 2. Insert two Pulleys (15), Pulleys (A1) and (A2), into Top Frame (F) under Cable (96)

and attach using for each pulley:

One 48 (3/8” x 2 3/4” hex head bolt)

Two 13 (pulley spacer)

One 56 (3/8” nylon lock nut)

C.

Route Cable (96) around Pulley (A3) as shown in diagram 1 and attach Pulley (A3) to Seated Press

Arm Support (N) as shown in diagram 2 using:

One 46 (3/8” x 7 1/2” hex head bolt)

Two 12 (metal spacer)

One 56 (3/8” nylon lock nut)

D.

See diagram 1. Feed Cable (96) above Pulley (A4) -already installed. Route Cable (96) around

Pulley (A4) and feed back between Pulley (A4) and Pulley (A6) -already installed.

E.

Route Cable (96) around Pulley (A5) as shown in diagram 1 and attach Pulley (A5) to Seated Press

Arm Support (N) as shown in diagram 2 using:

One 46 (3/8” x 7 1/2” hex head bolt)

Two 12 (metal spacer)

One 56 (3/8” nylon lock nut)

F.

See diagram 1. Feed Cable (96) back between Pulley (A4) and Pulley (A6) -already installed. Pull

entire length of Cable (96) through, and feed down through the hole in the small arm sticking out of

Angled Support Frame (E).

«
...
16
17
18
19
20
...
»

Содержание G5S








































Отзывы:

Нет отзывов