Body Solid G5S Скачать руководство пользователя страница 30 | Manualshive

Страница: 30 / 39

Body Solid G5S Скачать руководство пользователя страница 30

Be careful to assemble all components
in the sequence they are presented.

Inch

NOW IS THE TIME TO MAKE ALL NECESSARY

CABLE ADJUSTMENTS

After cable installation is complete you must check all cables for proper tension. Obvious signs that

cable tension problems exist include:

c

Top Plate (18) does not rest directly on the top Weight Stack Plate (25).

c

The holes in the Selector Bar (19) do not line up with holes in the Weight Stack Plates (25).

c

Cable(s) are sloppy and there is no resistance from the weight stack for the first few

inches of the exercise.

There are SEVEN areas for cable adjustment on the G5S:

A. Selector Rod Top Bolt (37).*

B. TWO adjustments in Double Adjustable Pulley Holder (CA).

C. FOUR Rubber Stops (23).

*SEE NOTE 1 ON PAGE 39

If there is to much tension, and the Top Plate (18) is not resting directly on the top weight stack plate:

1st. -Move pulley (A7) up, or Pulley (B3) down in the Double Adjustable Pulley Holder (CA).

2nd. -Turn and tighten one of the Rubber Stops (23).

If there is to much play or excessive slack:

1st. -Turn and loosen the Rubber Stop (23).

2nd. -Move Pulley (A7) down, or Pulley (B3) up in the Double Adjustable Pulley Holder (CA).

3rd. -Screw the Selector Rod Top Bolt (37) farther into the Selector Rod (19).

NOTE:

Cables should be inspected daily and adjusted periodically to ensure safe and

smooth operation.

NOTE:

After cable adjustment is complete, go back and tighten two bolts holding pulleys

in pulley housing on Double Adjustable Pulley Holder (CA).

30

15

mm

S T E P

«
...
28
29
30
31
32
...
»

Содержание G5S








































Отзывы:

Нет отзывов