Body Solid G5S Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 39

Body Solid G5S Скачать руководство пользователя страница 10

5

Be careful to assemble all components
in the sequence they are presented.

mm

Inch

A.

Slide two Plastic Bushings (78) into Back Pad Holder (T) as shown.

Attach Back Pad Holder (T) To Angled Support Frame (E) using:

Two 43 (1/2” x 3 1/4” hex head bolt)

Four 57 (1/2” washer)

Two 55 (1/2” nylon lock nut)

B.

Slide Convex End Cap (3) into Chrome Back Pad Frame (U) as shown.

Slide Chrome Back Pad Frame (U) into Back Pad Holder (T) and hold in place with

T-Shaped Pop Pin (26).

C.

Slide two 1” X 2” Convex End Caps (6) into Back Pad Frame (V) as shown.

Attach Back Pad Frame (V) to Chrome Back Pad Frame (U) as shown with a T-Shaped

Pop Pin (85), and using:

One 62 (3/8” x 5/8” allen bolt)

One 58 (3/8” washer)

D.

Attach two Leg Hold Downs (W) to the Angled Support Frame (E) using:

Two 53 (3/8” x 3 1/4” hex head bolt)

Four 58 (3/8” washer)

Two 56 (3/8” nylon lock nut)

C.

Attach two Foam Rollers (17) onto Leg Hold Downs (W) and hold in place with two Roller End

Caps (8) as shown.

F.

Attach Back Pad (X) to Back Pad Frame (V) using:

Two 51 (5/16” x 1 3/4” hex head bolt)

Two 60 (5/16” spring lock washer)

Two 59 (5/16” washer)

G.

Insert Flat Allen Head Bolt (69) into Chrome Back Pad Frame (U), this will help hold the Chrome

Back Pad Frame (U) in place.

10

NOTE:

Finger tighten all hardware in this step. Do Not wrench tighten until end of step 7.

S T E P

«
...
8
9
10
11
12
...
»

Содержание G5S








































Отзывы:

Нет отзывов