manualshive.com logo in svg

Body Solid G5S, Руководство по сборке, Страница: 14 / 39

Поделиться
Скачать
Body Solid G5S Скачать руководство пользователя страница 14

7

Be careful to assemble all components
in the sequence they are presented.

mm

Inch

A.

Place two Weight Stack Risers (89) and two Rubber Donuts (10) onto Main Base Frame (A) as 

shown. Slide two Guide Rods (AA) through the Rubber Donuts (10), through the two Weight Stack

Risers (89), and into the Main Base Frame (A).

B.

Slide Weight Stack Plates (25) onto Guide Rods (AA). Make sure the opening in each Weight 

Stack Plate (25), for the Weight Stack Pin (1), is facing outward.

C.

Connect Top Plate (18) to the Selector Rod (19) using:

One 61 (3/8” X 1 1/2” round allen head)

Slide Top Plate (18) and Selector Rod (19) onto Guide Rods (AA).

D.

Slide two Shaft Collars (24) onto the two Guide Rods (AA) as shown.

E.

Insert Guide Rods (AA) into Top Weight Stack Frame (AB), and Attach Top Weight Stack

Frame (AB) to Top Frame (F) using:

Two 50 (3/8” x 1” hex head bolt)

Two 58 (3/8” washer)

Attach Curved End Cap (3) to Top Weight Stack Frame (AB) as shown.

F.

Slide Shaft Collars (24) up into the Top Weight Stack Frame (AB) and turn the Shaft Collar, so the 

Shaft Collars (24) lock onto the Top Weight Stack Frame (AB), Now tighten each Allen Screw (27) 

in Shaft Collars (24). 

G.

At this point you can now wrench tighten all bolts and nuts on the main frame unit.

14

S T E P

Содержание G5S








































Отзывы:

Нет отзывов