SMARTLINK
I&II
MDS921AE-10BTS - MDS
Exit
If you want to exit the system without saving, use
Setup
All of the setup parameters are located in the subdirectories of setup. Move the cursor “
setup
and press enter.
>> mode
Switch system operation mode
shdsl
Configure SHDSL parameters
shdsl.bis
Configure SHDSL.bis parameters
wan
Configure WAN interface profile
bridge
Configure transparent bridging
Vlan
Configure virtual LAN paramters
Stp
Configures Spanning Tree Protocol of the Router
route
Configure routing parameters
lan
Configure LAN interface profile
ip_share
Configure NAT/PAT parameters
firewall
Configure Firewall parameters
Ip_qos
Configure IP QoS parameters of the router
dhcp
Configure DHCP parameters
dns_proxy
Configure DNS proxy parameters
hostname
Configure local host name
default
Restore
Mode
The product can act as routing mode or bridging mode. The default setting is routing mode. You
can change the system operation mode by using mode command. Move the cursor “
and press enter.
----------------------------------------------------------------------
Command: setup mode <Route|Bridge>
Message: Please input the following information.
System operation mode (TAB select) <Route>:
----------------------------------------------------------------------
SHDSL
You can setup the SHDSL parameters by the command
press enter.
>> mode
Configure SHDSL mode
n*64
Configure SHDSL data rate
type
Configure SHDSL annex type
clear
Clear current CRC error count
margin
Configure SHDSL SNR margin
There are two types of SHDSL mode, STU
office and STU-C customer premises equipment.
You can setup the data rate by the multiple of 64Kbps where n is from 0 to 32. If you configure n is
0, the product will perform as adaptive mode.
There are two types of SHDSL Annex type, Annex
S957AE-10BTS User Manual
Page 99 of 113
If you want to exit the system without saving, use
exit
command to quit system.
All of the setup parameters are located in the subdirectories of setup. Move the cursor “
Switch system operation mode
Configure SHDSL parameters
Configure SHDSL.bis parameters
Configure WAN interface profile
Configure transparent bridging
Configure virtual LAN paramters
Configures Spanning Tree Protocol of the Router
Configure routing parameters
Configure LAN interface profile
Configure NAT/PAT parameters
Configure Firewall parameters
Configure IP QoS parameters of the router
Configure DHCP parameters
Configure DNS proxy parameters
Configure local host name
Restore factory default setting
The product can act as routing mode or bridging mode. The default setting is routing mode. You
can change the system operation mode by using mode command. Move the cursor “
----------------------------------------------------------------------
Command: setup mode <Route|Bridge>
Message: Please input the following information.
System operation mode (TAB select) <Route>:
Route
----------------------------------------------------------------------
You can setup the SHDSL parameters by the command
shdsl
. Move the cursor “
Configure SHDSL mode
Configure SHDSL data rate
Configure SHDSL annex type
Clear current CRC error count
Configure SHDSL SNR margin
There are two types of SHDSL mode, STU-R and STU-C. STU-R means the terminal of central
C customer premises equipment.
can setup the data rate by the multiple of 64Kbps where n is from 0 to 32. If you configure n is
0, the product will perform as adaptive mode.
There are two types of SHDSL Annex type, Annex-A and Annex-B.
command to quit system.
All of the setup parameters are located in the subdirectories of setup. Move the cursor “
>>
“ to
The product can act as routing mode or bridging mode. The default setting is routing mode. You
can change the system operation mode by using mode command. Move the cursor “
>>
“ to
mode
. Move the cursor “
>>
“ to shdsl and
R means the terminal of central
can setup the data rate by the multiple of 64Kbps where n is from 0 to 32. If you configure n is
