SMARTLINK
I&II
MDS921AE-10BTS - MDS
To assign PVID (Port VID), move the cursor “>>” to PVID and press enter. The port index 1 to 4
represents LAN1 to LAN4 respectively an
which you want to assign the PVID of the port. PVID is
----------------------------------------------------------------------
Command: setup vlan pvid <1~5> <1~4094>
Message: Please input the follo
Port index <1~1>:
1
VID Value (Enter for default) <10>:
----------------------------------------------------------------------
To modify the link type of the port, move the cursor to link mode and press enter. There are two
types of link: access and trunk. Trunk link will send the tagged packet form the port and access link
will send un-tagged packet form the port. Port index 1 to 4 represents LAN1 to LAN4 respectively.
According to the operation mode of the device, link type of WAN
the product operates in bridge mode, the WAN link type will be trunk, and in routing mode, access.
----------------------------------------------------------------------
Command: setup vlan link_mode <1~4> <Access|Tru
Message: Please input the following information.
Port index <1~4>:
1
Port link type (Tab select) <Trunk>:
----------------------------------------------------------------------
To view the VLAN table, move the cursor to list and press enter.
STP
IEEE 802.1d to implement this feature for avoiding a storm in a redundant network
environment The default is disable.
>> active
Trigger Bridge STP function
Once you enable the STP feature, you can see the STP status will follow IEEE 802.1d
work. The working steps are Blocking, Listening, Learning and forwarding.
It will send BPDU, a hello packet to make sure if the network is still stable. Once it can’t receive the
hello packet over the max. 20 sec., it will restart to process t
Route
You can setup the routing parameters in route command. If the product is configured as a bridge,
you do not want to setup the route parameters. Move the cursor “
>> static
Configure static routing
rip
Configure RIP tool
If the Router is connected to more than one network, it may be necessary to set up a static route
between them. A static route is a pre
reach a specific host or network.
With Dynamic Routing, you can enable the Router to automatically adjust to physical changes in
the network’s layout. The Cable/DSL Firewall Router, using the RIP protocol, determines the
S957AE-10BTS User Manual
Page 104 of 113
To assign PVID (Port VID), move the cursor “>>” to PVID and press enter. The port index 1 to 4
represents LAN1 to LAN4 respectively and port index 5 represents WAN. VID value is the group at
which you want to assign the PVID of the port. PVID is
----------------------------------------------------------------------
Command: setup vlan pvid <1~5> <1~4094>
Message: Please input the following information.
VID Value (Enter for default) <10>:
10
----------------------------------------------------------------------
To modify the link type of the port, move the cursor to link mode and press enter. There are two
link: access and trunk. Trunk link will send the tagged packet form the port and access link
tagged packet form the port. Port index 1 to 4 represents LAN1 to LAN4 respectively.
According to the operation mode of the device, link type of WAN port is automatically configured. If
the product operates in bridge mode, the WAN link type will be trunk, and in routing mode, access.
----------------------------------------------------------------------
Command: setup vlan link_mode <1~4> <Access|Trunk>
Message: Please input the following information.
Port link type (Tab select) <Trunk>:
Access
----------------------------------------------------------------------
To view the VLAN table, move the cursor to list and press enter.
IEEE 802.1d to implement this feature for avoiding a storm in a redundant network
environment The default is disable.
Trigger Bridge STP function
Once you enable the STP feature, you can see the STP status will follow IEEE 802.1d
work. The working steps are Blocking, Listening, Learning and forwarding.
It will send BPDU, a hello packet to make sure if the network is still stable. Once it can’t receive the
hello packet over the max. 20 sec., it will restart to process the above 4 steps.
You can setup the routing parameters in route command. If the product is configured as a bridge,
you do not want to setup the route parameters. Move the cursor “
>>
“ to
route
Configure static routing table
Configure RIP tool
If the Router is connected to more than one network, it may be necessary to set up a static route
between them. A static route is a pre-determined pathway that network information must travel to
network.
With Dynamic Routing, you can enable the Router to automatically adjust to physical changes in
the network’s layout. The Cable/DSL Firewall Router, using the RIP protocol, determines the
To assign PVID (Port VID), move the cursor “>>” to PVID and press enter. The port index 1 to 4
d port index 5 represents WAN. VID value is the group at
To modify the link type of the port, move the cursor to link mode and press enter. There are two
link: access and trunk. Trunk link will send the tagged packet form the port and access link
tagged packet form the port. Port index 1 to 4 represents LAN1 to LAN4 respectively.
port is automatically configured. If
the product operates in bridge mode, the WAN link type will be trunk, and in routing mode, access.
IEEE 802.1d to implement this feature for avoiding a storm in a redundant network
Once you enable the STP feature, you can see the STP status will follow IEEE 802.1d standard to
It will send BPDU, a hello packet to make sure if the network is still stable. Once it can’t receive the
he above 4 steps.
You can setup the routing parameters in route command. If the product is configured as a bridge,
route
and press enter.
If the Router is connected to more than one network, it may be necessary to set up a static route
determined pathway that network information must travel to
With Dynamic Routing, you can enable the Router to automatically adjust to physical changes in
the network’s layout. The Cable/DSL Firewall Router, using the RIP protocol, determines the
