SMARTLINK
I&II
MDS921AE-10BTS - MDS
For two-pair mode
Link Type.
Please select the desired operation mode of the router.
2-Wire:
2-wire mode, second pair is d
M-Pair
4-wire mode. If one of two pairs fails, all link breaks
M-Pair (Conexant)
4-wire mode.
Auto Fall Back
4-wire mode. Two pairs works s
goes through the other pair.
Standby
4-wire mode. Only one pair works, another pair is in standby. When one
pair fails, fraffic goes through the other pair.
Multi-link
4-wire mode. Each pair is connected to two d
be or may not be in same location
Data Rate (4W)
: you can setup the SHDSL.bis data rate in the multiple of 128kbps.
The default data rate is 11392Kbps (n=89).
Under Annex F/G
TCPAM32 ; data rate is 1536Kbps ~ 11392Kbps
TCPAM16 ; data rate is 384Kbps ~ 7680Kbps (Nx128kbps, N=3~60)
Under Annex A/B
TCPAM16 ; 384Kbps ~ 4608Kbps (Nx 128kbps, N=3~36)
For adaptive mode, you have to setup n=0. The router will adapt the data rate according to the line
status.
SNR margin is an index of line connection quality. You can see the actual SNR margin in STATUS
SHDSL.bis. The larger is SNR margin; the better is line connection quality.
If you set SNR margin in the field as 2, the SHDSL.bis connection will drop and
SNR margin is lower than 2. On the other hand, the device will reduce the line rate and reconnect
for better line connection quality.
The screen will prompt the parameters that will be written in EPROM. Check the parameters before
writing in EPROM.
Press Restart to restart the router working with new parameters or press continue to setup another
parameter.
S957AE-10BTS User Manual
Page 40 of 113
operation mode of the router.
wire mode, second pair is disabled
wire mode. If one of two pairs fails, all link breaks
wire mode. Extended compatibility with Conexant IC
wire mode. Two pairs works simultaneously. When one pair fails, traffic
goes through the other pair.
wire mode. Only one pair works, another pair is in standby. When one
pair fails, fraffic goes through the other pair.
wire mode. Each pair is connected to two different devices, which may
be or may not be in same location
: you can setup the SHDSL.bis data rate in the multiple of 128kbps.
The default data rate is 11392Kbps (n=89).
TCPAM32 ; data rate is 1536Kbps ~ 11392Kbps (Nx128kbps, N=12~ 89)
TCPAM16 ; data rate is 384Kbps ~ 7680Kbps (Nx128kbps, N=3~60)
TCPAM16 ; 384Kbps ~ 4608Kbps (Nx 128kbps, N=3~36)
For adaptive mode, you have to setup n=0. The router will adapt the data rate according to the line
SNR margin is an index of line connection quality. You can see the actual SNR margin in STATUS
SHDSL.bis. The larger is SNR margin; the better is line connection quality.
If you set SNR margin in the field as 2, the SHDSL.bis connection will drop and
SNR margin is lower than 2. On the other hand, the device will reduce the line rate and reconnect
for better line connection quality.
The screen will prompt the parameters that will be written in EPROM. Check the parameters before
Press Restart to restart the router working with new parameters or press continue to setup another
Extended compatibility with Conexant IC
imultaneously. When one pair fails, traffic
wire mode. Only one pair works, another pair is in standby. When one
ifferent devices, which may
: you can setup the SHDSL.bis data rate in the multiple of 128kbps.
For adaptive mode, you have to setup n=0. The router will adapt the data rate according to the line
SNR margin is an index of line connection quality. You can see the actual SNR margin in STATUS
If you set SNR margin in the field as 2, the SHDSL.bis connection will drop and reconnect when the
SNR margin is lower than 2. On the other hand, the device will reduce the line rate and reconnect
The screen will prompt the parameters that will be written in EPROM. Check the parameters before
Press Restart to restart the router working with new parameters or press continue to setup another
