SMARTLINK
I&II
MDS921AE-10BTS - MDS
•
Frames are sent out tagged or untagged depend on if the egress port is a tagged
untagged member of the VLAN that frames belong to.
•
If VID and source address look up fails, the source address will be learned.
You can setup the Virtual LAN (VLAN) parameters in vlan command.
implementation of VLAN-to-PVC only f
the COE and CPE sides, where there is no layer 3 routing involved
active VLANs with shared VLAN learning (SVL) bridge out of 4096 possible VLANs specified in
IEEE 802.1Q.
Move the cursor “
>>
“ to
vlan
>> mode
Trigger virtual LAN function
modify
Modify virtual LAN rule
pvid
Modify port default ID
link_mode
Modify port link type
list
Show VLAN configuration
To active the VLAN function, move the cursor “
support two types of VLAN, 802.11q and Port
VLAN bridges that permit the definition, operation, and administration of
bridged LAN infrastructure. Port
based on the destination MAC address and its associated port.
802.11Q VLAN
Follow the following steps to configure 802.11q VLAN.
----------------------------------------------------------------------
Command: setup vlan active <Disable|8021Q|Port>
Message: Please input the following information.
Tigger VLAN function (Tab select) <Disable>:
----------------------------------------
To modify the VLAN rule, move the cursor “
----------------------------------------------------------------------
Command: setup vlan modify <1~8> <1~4094> <string>
Message: Please input the following information.
Rule entry index <1~8>:
1
VLAN ID (Enter for default) <1>:
VLAN port status (Enter for default): 11001
----------------------------------------------------------------------
For each VLAN, VLAN ID is a unique number among
VLAN port status is a 5-digit binary number whose bit
membership in which 4MSBs and 1MSB represents LAN ports and WAN port, respectively. For
example: the above setting means that the VID 20 member port includes
The member ports are tagged members. Use PVID command to change the member port to
untagged members
S957AE-10BTS User Manual
Page 103 of 113
Frames are sent out tagged or untagged depend on if the egress port is a tagged
untagged member of the VLAN that frames belong to.
If VID and source address look up fails, the source address will be learned.
You can setup the Virtual LAN (VLAN) parameters in vlan command. The router support the
PVC only for bridge mode operation, i.e., the VLAN spreads over both
the COE and CPE sides, where there is no layer 3 routing involved. The unit supports up to 8
active VLANs with shared VLAN learning (SVL) bridge out of 4096 possible VLANs specified in
vlan
and press enter.
Trigger virtual LAN function
Modify virtual LAN rule
Modify port default ID
Modify port link type
Show VLAN configuration
To active the VLAN function, move the cursor “
>>
“ to mode and press enter. The products
support two types of VLAN, 802.11q and Port-Based. The IEEE 802.1Q defines the operation of
VLAN bridges that permit the definition, operation, and administration of VLAN topologies within a
bridged LAN infrastructure. Port-Based VLANs are VLANs where the packet forwarding decision is
based on the destination MAC address and its associated port.
Follow the following steps to configure 802.11q VLAN.
-----------------------------------------------------------------
Command: setup vlan active <Disable|8021Q|Port>
Message: Please input the following information.
Tigger VLAN function (Tab select) <Disable>:
8021Q
----------------------------------------------------------------------
To modify the VLAN rule, move the cursor “
>>
“ to modify and press enter.
----------------------------------------------------------------------
Command: setup vlan modify <1~8> <1~4094> <string>
following information.
VLAN ID (Enter for default) <1>:
10
VLAN port status (Enter for default): 11001
----------------------------------------------------------------------
For each VLAN, VLAN ID is a unique number among 1~4095.
digit binary number whose bit-1 location indicates the VLAN port
membership in which 4MSBs and 1MSB represents LAN ports and WAN port, respectively. For
example: the above setting means that the VID 20 member port includes LAN1, LAN2 and WAN.
The member ports are tagged members. Use PVID command to change the member port to
Frames are sent out tagged or untagged depend on if the egress port is a tagged or
If VID and source address look up fails, the source address will be learned.
The router support the
or bridge mode operation, i.e., the VLAN spreads over both
The unit supports up to 8
active VLANs with shared VLAN learning (SVL) bridge out of 4096 possible VLANs specified in
“ to mode and press enter. The products
The IEEE 802.1Q defines the operation of
VLAN topologies within a
Based VLANs are VLANs where the packet forwarding decision is
1 location indicates the VLAN port
membership in which 4MSBs and 1MSB represents LAN ports and WAN port, respectively. For
LAN1, LAN2 and WAN.
The member ports are tagged members. Use PVID command to change the member port to
