Black Box LRU4240 Скачать руководство пользователя страница 140

Страница: 140 / 218

128

SALES: 0118 965 5100

Dual Trunk E1 Router User’s Guide

Dual Trunk E1 Router

Table D-34 Menu-6B Multilink Frame Relay Port Configuration and Status

Table D-35 Menu-7 Feature Keys

Table D-36 Alarm Configuration

Protocol Error -

Number of PPP/MLPPP protocol errors detected in this port.

Paramete
r

Description

Default

Port 1/2

Include In Bundle

- Yes, No

Yes

Status

- Normal, Idle, Down, Remote Not Configured, Inconsistent Bundle,

Unknown Vendor, Loopback Detected, Test Active, Remote Link Up, and Awaiting
Remote Link

(status)

Protocol Errors

- number of MFR protocol errors detected on the port

(counter)

Local

Local Bundle Identifier -

(status) local identifier for logical T1 bundle

(ID no.)

Remote Bundle Identifier -

(status) remote identifier for logical T1 bundle

(ID no.)

Parameter

Default

RMON

– PPP and Frame Relay RMON1 statistics

Capable

Service Level Agreement (Frame Relay SLA FRF.13)

Capable

RMON 2 -

Protocols and application monitoring

Capable

Access Router 2 Ports

–

Capable

Access Router single port

Not capable

Dynamic Routing

Capable

Primary
Parameters

Parameter—Options;
Definition

Default

NET Alarms

Block All Alarms

—Yes, No

Yes—Blocks the reporting of all alarms.
No—Enables the unit to report alarms.

Carrier Loss Alarm

—Enabled, Disabled

Enabled—The unit generates an alarm when a network carrier Loss of
Signal is detected on the network.
Disabled—Disables the alarm.

Sync Loss Alarm

—Enabled, Disabled

Enabled—The unit generates an alarm when loss-of-frame is detected on
the network.
Disabled—Disables the alarm.

Enabled

Parameter

Description

Содержание LRU4240



























































































































































































































Результаты поиска

Содержание LRU4240

Отзывы:

Похожие инструкции для LRU4240

Бренды по названию

Популярные бренды

Black Box LRU4240, Руководство пользователя

Результаты поиска

Содержание LRU4240

Отзывы:

Похожие инструкции для LRU4240

Бренды по названию

Популярные бренды