Black Box LRU4240 Скачать руководство пользователя страница 70 | Manualshive

Страница: 70 / 218

background image

58

SALES: 0870 90 10 750

Dual Trunk E1 Router User’s Guide

Dual Trunk E1 Router

• Static NAT - To map a unregistered IP address to a registered IP address. This is useful to enable

outside hosts to access an internal IP host of server.

• Dynamic NAT - To share dynamically a range of global addresses among internal hosts to access

the internet. Translation occurs when traffic takes place.

• Overloading - If the number of global addresses available is less than number of hosts which

need to access internet at the same time, then the port field also can be used for translation.
Unregistered IP addresses are mapped to one or many registered IP addresses.

NAT Configuration menus

NAT is configurable through the TUI menu $J accessible direcly or remotely via Telnet.

Table 6-5

NAT configuration menus

Menu

Description

Menu-$JA Global Map table

To configure the global IP address ranges to allocate through NAT.

Select

Add

command

Add the global IP addresses to NAT.

Menu-$JB NAT static table

To configure the one-to-one mapping of global IP addresses to local IP
addresses.

Menu-$C-Local address table

To configure the networks that require NAT translation. If the table is empty
no NAT translation will take place.
NAT will translate if the packet source or destination IP address is included
in the Local table.
NAT will not translate if both the packet source AND the destination IP
addresses are included in the local table. This is useful for network scenarios
where filtering NAT, based on source and destination addres, is required.

Menu-$JE NAT Interface
configuration

To enable or disable NAT and NAPT per WAN interface.

Menu-$JF NAT Dynamic entries

To verify dynamic operations. You can view the dynamic alloction of global
IP addresses to local host as traffic takes place.

«
...
68
69
70
71
72
...
»

Содержание LRU4240



























































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для LRU4240

Бренд: Paradyne Страницы: 11

Бренд: Paradyne Страницы: 19

Бренд: Paradyne Страницы: 32

COMSPHERE 3550 Series

Бренд: Paradyne Страницы: 153

Jetstream CPX-1000

Бренд: Paradyne Страницы: 141

FrameSaver 9783

Бренд: Paradyne Страницы: 28

COMSPHERE 6800 Series

Бренд: Paradyne Страницы: 7

Parallel & Serial Port Checker PPC

Бренд: B&B Electronics Страницы: 4

TE100-S16 - 10/100Mbps Ethernet Switch

Бренд: TRENDnet Страницы: 15

Enterasys Matrix 2G4082-25

Бренд: Enterasys Страницы: 58

Бренд: B&B Electronics Страницы: 2

Бренд: Infoblox Страницы: 13

SinoCon C2000-C2-SHK0401-BB1

Бренд: KonNad Страницы: 12

Бренд: CalAmp Страницы: 115

Бренд: Razer Страницы: 17

Бренд: Topcom Страницы: 16

Бренд: Juniper Страницы: 420

Бренд: FiberHome Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды