Black Box LRU4240 Скачать руководство пользователя страница 51

Страница: 51 / 218

Dual Trunk E1 Router

Dual Trunk E1 Router User’s Guide

TECHNICAL: 0118 96 56 000

Configuring independent PPP links Interfaces

The PPP connection over the first T1/E1 port is assigned the interface port NET1. The second
T1/E1 port is assigned the interface port NET2.

Configuring MLPPP Interface

Configuring PPP Protocol Parameters

Menu 6-A lets you configure the PPP or MLPPP protocol parameters:

Table 4-8

Menu-6A PPP Configuration

Procedure

Purpose

Set router traffic type to PPP

1.Set Menu-0A- Traffic type field to PPP.

2.Set Menu-0A Multilink Protocol field to No.

Set WAN port 1 IP address

1.Set Menu-0A NET1 IP address and subnet mask

Assign an IP address and subnet mask to the second T1/E1 link. This will
be identified as NET1 link in all the menus.

Set WAN port 2 IP address

1.Set Menu-0A NET2 IP address and subnet mask

Assign an IP address and subnet mask to the second T1/E1 link. This will
be identified as NET2 link in all the menus

Procedure

Purpose

Set router traffic type to MLPPP

1.Set Menu-0A- Traffic type field to PPP.

2.Set Menu-0A Multilink Protocol field to Yes

The menus will be configured for MLPPP operations. The bottom menu
will display “MLPPP Cfg”

Set WAN bundle connection IP
Address

1.Set Menu-0A NET IP address and subnet mask

Assign IP address and subnet mask to the bundle link associated to the
bundled T1/E1 links. The bundle link is identified as Bundle0 link in all the
menus.

Parameter

Description

Keep alive timer

Controls the messages of the keepalive (echo request) messages after the link(s)
is(are) negotiated

Keep alive timeout

Controls how long an end point should wait for “ech response” after ending “echo
request”

Retry Counter

How many unsuccessful “echo requests” should be attempted before a link is
declared down

Содержание LRU4240



























































































































































































































Результаты поиска

Содержание LRU4240

Отзывы:

Похожие инструкции для LRU4240

Бренды по названию

Популярные бренды

Black Box LRU4240, Руководство пользователя

Результаты поиска

Содержание LRU4240

Отзывы:

Похожие инструкции для LRU4240

Бренды по названию

Популярные бренды