manualshive.com logo in svg

Black Box LRU4240, Руководство пользователя

Пользовательский мануал к Black Box LRU4240 доступен для бесплатного скачивания на manualshive.com. Узнайте все возможности и настройки вашего устройства, чтобы его использование было максимально эффективным. Скачайте мануал сейчас и овладейте всеми функциями Black Box LRU4240.

Поделиться
Скачать
background image

Dual Trunk E1 Router

Dual Trunk E1 Router User’s Guide

TECHNICAL:  0118 931 2233 

115

TRAP
2nd Output Port

COMM, ENET, NET
Selects the DLCI (if applicable) and port over which the router will send a trap to the 
2nd NMS IP address.

TRAP 
3rd Output Port

COMM, ENET, NET
Selects the DLCI (if applicable) and port over which the router will send a trap to the 
2nd NMS IP address.

Table D-4 Menu-0C Ethernet Configuration

Parameter

Description

MAC Address

Read-only  Ethernet port MAC address assigned at factory.

Data speed mode

Ethernet port speed 10MB/Half (default) or  10MB/Full

ProxyARP 

Reserved for IP Fast Forwarding mode. This feature is no longer supported. 
Enable or disable ProxyARP in Fast forwarding mode. Default is disabled.

Net directed broadcast 
mode

Reserved for IP Fast Forwarding mode. This feature is no longer supported. 
Configurable option available in Fast Forwarding mode only. Enter the network 
directed broadcast IP address mask

Fwd Multicast

Reserved for IP Fast Forwarding mode. This feature is no longer supported. 
Configurable option available in Fast Forwarding mode only. Enable or disable 
forwarding mulcast packets.

Table D-5 Menu-0E Performance Monitoring Configuration

Parameter

Parameter - Options; Definition

Interface

The network interface (NET1, NET2, or NET) to  which the DLCI is attached

DLCI

DLCIs will be autodiscovered if LMI is enabled on menu-0F. If LMI is not enabled, the 
DLCIs must be entered manually on this table.
To change a DLCI status to Deleted, enter a zero for the DLCI number. If LMI is 
enabled, and the DLCI still exists, it will be discovered again and its status returned toa 
active.
Default: 0

CIR

The Committed information rate. If LMI revision 1 is being used, this will be 
discovered; otherwise, you will need to enter the CIR for each DLCI
Default: 0

Delay Threshold

The range is 0 to 64000 milliseconds. When the round trip delay over the PVC exceeds 
this value:

• An event will be registered in the Event Log

• A trap will be sent to the NMS (if configured)

• An alarm message will be displayed on the terminal user interface

• A delay threshold violation is counted

Table D-3 Menu-0B SNMP Configuration

Parameter

Description

Содержание LRU4240



























































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для LRU4240

TDC Netopia User Manual preview
Netopia
Бренд: TDC Страницы: 27
Wattle Pegasus Quick Installation Manual preview
Pegasus
Бренд: Wattle Страницы: 6
Baicells Nova430i Quick Manual preview
Nova430i
Бренд: Baicells Страницы: 8
E-Tech Wireless Mini PCI Module User Manual preview
Wireless Mini PCI Module
Бренд: E-Tech Страницы: 42
Accton Technology Fast SwitchHub-8mi SNMP Advanced Reference Manual preview
Fast SwitchHub-8mi SNMP
Бренд: Accton Technology Страницы: 13
Xircom RealPort Ethernet 10/100 User Manual preview
RealPort Ethernet 10/100
Бренд: Xircom Страницы: 30
Tektronix CTS 850 User Manual preview
CTS 850
Бренд: Tektronix Страницы: 178
ZoneVu ZSI-450-IP Installation Manual & User Manual preview
ZSI-450-IP
Бренд: ZoneVu Страницы: 15
Matrix Switch Corporation MSC-1HD1608L Product Manual preview
MSC-1HD1608L
Бренд: Matrix Switch Corporation Страницы: 60
Abocom SDW11B Specification Sheet preview
SDW11B
Бренд: Abocom Страницы: 1
RadioSPECTRAL ICOM IC-7300 Installation Manual preview
ICOM IC-7300
Бренд: RadioSPECTRAL Страницы: 2
NetComm RTA100 User Manual preview
RTA100
Бренд: NetComm Страницы: 75
Proscend 6200-2W User Manual preview
6200-2W
Бренд: Proscend Страницы: 93
Omron JUNMA PULSE Datasheet preview
JUNMA PULSE
Бренд: Omron Страницы: 4
ZyXEL Communications ONU5100-B22 User Manual preview
ONU5100-B22
Бренд: ZyXEL Communications Страницы: 2
ZyXEL Communications GS1900 Series User Manual preview
GS1900 Series
Бренд: ZyXEL Communications Страницы: 263
OST RuggedNet 10G/Si User Manual preview
RuggedNet 10G/Si
Бренд: OST Страницы: 8
Proxim 68568r1 Installation And Management Manual preview
68568r1
Бренд: Proxim Страницы: 65

Бренды по названию

Популярные бренды

Загрузить еще бренды