Black Box LRU4240 Скачать руководство пользователя страница 115 | Manualshive

Страница: 115 / 218

background image

Dual Trunk E1 Router

Dual Trunk E1 Router User’s Guide

TECHNICAL: 0118 96 56 000

103

Software Upgrade

C

S

OFTWARE

D

OWNLOAD

The Download feature enables you to upgrade software, and includes the following capabilities:

• Separates the downloading operation from switching to new software, where these operations

can be performed at separate times. You can schedule a time at which the unit can be initialized
with the new code.

• Command remotely using SNMP the TFTP/XModem download and code switching
• The unit stores two images of executable code; you can switch between the two images.

• Enables downloading of the new software while the unit is operational and passing data. The

code can be downloaded through:

• Xmodem via the terminal user interface using an asynchronous connection.

• TFTP from a network management station to the unit via SLIP using an asynchronous

connection or through NET or Ethernet Ports in-band.

• TFTP via Ethernet.

Using the Download Menu Utility

Use the Download Utility menu, accessed through Menu-4, Main Configuration, to download
software updates. You may use the Xmodem protocol or TFTP. When switching from one
executable image to another, the operational software in the unit is restarted, which results in a
temporary service interruption lasting from one to two minutes.

During the download sequence, the Power/Test LED will blink alternating red and green.

Setting Up for Xmodem

To download new software:

1. Insert the new software diskette in the drive of the PC.

2. From Menu-4 Main Configuration, type

F

(as instructed in the menu for FLASH

Download) to start the download session.

3. Menu 4F (Software Download Menu) will appear

4. Select the Protocol (Xmodem or TFTP) to Xmodem under

Protocol

.

5. Press

A

to start the download.

Setting Up for TFTP

Use these steps to set up for TFTP::

1. Set the download protocol in the Download utility to TFTP.

«
...
113
114
115
116
117
...
»

Содержание LRU4240



























































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для LRU4240

DES-3526 - Switch - Stackable

Бренд: D-Link Страницы: 258

Бренд: D-Link Страницы: 32

Бренд: D-Link Страницы: 6

Бренд: D-Link Страницы: 221

ShareCenter Pro DNS-1200-05

Бренд: D-Link Страницы: 68

Express Ethernetwork DI-707P

Бренд: D-Link Страницы: 14

DHI-NVR5224-24P-4KS2

Бренд: Dahua Страницы: 24

Бренд: Hama Страницы: 10

Бренд: Paradyne Страницы: 2

Бренд: Paradyne Страницы: 20

Бренд: Paradyne Страницы: 2

Бренд: Zhone Страницы: 2

COMSPHERE 6800 Series

Бренд: Paradyne Страницы: 155

COMSPHERE 6800 Series

Бренд: Paradyne Страницы: 44

HiGain HLU-231 List 8F

Бренд: ADC Страницы: 7

Бренд: Teac Страницы: 20

cMT-FHDX Series

Бренд: Maple Systems Страницы: 2

Бренд: NETGEAR Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды