Black Box LRU4240 Скачать руководство пользователя страница 161 | Manualshive

Страница: 161 / 218

background image

Dual Trunk E1 Router

Dual Trunk E1 Router User’s Guide

TECHNICAL: 0118 96 56 000

149

unit(config)#

t1 lbo

Use the

t1 lbo

command to to set the Line Build Out (LBO) value to be used for tuning the circuit attenuation between the unit

and the last repeater on the T1 circuit.

Command Syntax

: t1 lbo [0dB | -7.5dB | -15 dB]

Command Mode:

Config

Example

t1 timeslot

Use the

t1 timeslot

command to allocate an T1 timeslot and assign it to data, voice or idle.

Command Syntax

: t1 timeslot <1-23> [aux | f1 | idle]

<1-31> select an E1 timeslot number
aux     Assign selected timeslot to auxiliary dro-and-insert port
f1       Assign selected timeslot to Ethernet data port
idle     Selected timeslot will not be used

Command Mode:

Config

Example

Assign timeslot 10 to transport data from Ethernet data port.
unit(config)#e1 timeslot 10 f1

time-sync

Use the

time-sync

command to configure the RFC-868 time protocol client.

Command Syntax

:

time-sync [enabled | disabled] Enable of disables time synchronization.
time-sync attempt-count [1-30]
time-sync attempt-interval [1-10]
time-sync frequency days [0-99]
time-sync frequency hours [0-23]
time-sync frequency minutes [0-59]
time-sync frequency seconds [0-59]
time sync primary-ip A.B.C.D
time-sync secondary-ip A.B.C.D
time-sync port [enet | net | comm]

time-zone

Use the

time-zone

command to configure the GMT time zone.

Command Syntax

:

time-zone ahead-gmt [yes | no]
time-zone day-light-savings [enabled | disabled]
time-zone day-light-savings diff-minutes [0-59]
time-zone day-light-savings start-month [0-12]
time-zone day-light-savings start-week [0-5]
time-zone offset-gmt minutes [0-59]
time-zone day-light-savings diff-hours [0-12]
time-zone offset-gmt hours [0-12]

traffic monitoring

Use the

traffic monitoring

command to enable or disable RMON1 and RMON2 traffic monitoring.

Command Syntax

:

traffic monitoring [enabled | disabled]

«
...
159
160
161
162
163
...
»

Содержание LRU4240



























































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для LRU4240

Бренд: Patton electronics Страницы: 2

SMART NODE 4950-NCE

Бренд: Patton electronics Страницы: 8

NetLink 2960 RAS

Бренд: Patton electronics Страницы: 2

Бренд: Patton electronics Страницы: 2

Бренд: Qlogic Страницы: 20

3C13886 - Router OC-3 ATM SML Flexible Interface...

Бренд: 3Com Страницы: 171

OfficeConnect WX2200

Бренд: 3Com Страницы: 204

Fieldpoint cFP-RTD-124

Бренд: National Instruments Страницы: 15

Бренд: Magnadyne Страницы: 8

JetStream T2600G-28TS

Бренд: TP-Link Страницы: 1136

Бренд: Comelit Страницы: 140

TigerSwitch 100 SMC6924VF

Бренд: SMC Networks Страницы: 174

Бренд: Netopia Страницы: 138

DiskStation Series

Бренд: Synology Страницы: 6

Бренд: N-Tron Страницы: 2

Бренд: Tripp Lite Страницы: 3

IPSec VPN Client Zyxel ZyWall 10

Бренд: TheGreenBow Страницы: 12

Бренд: IBM Страницы: 70

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды