Black Box LRU4240 Скачать руководство пользователя страница 159 | Manualshive

Страница: 159 / 218

background image

Dual Trunk E1 Router

Dual Trunk E1 Router User’s Guide

TECHNICAL: 0118 96 56 000

147

Use the

ip route

command to set static routes that map destination IP addresses to next hop IP address or interface. Static routes

can be edited, changed, viewed from menu$-JC.

Command Syntax

:

ip route A.B.C.D/M IFNAME metric <0-255>

Static route mapping destination IP address to interface port
A.B.C.D/M Static route destination IP address field
IFNAME the [net1 | net2 | bundle0 | enet0] interface port
metric <0-255> Static route metric field in seconds

ip route A.B.C.D/M A.B.C.D metric [0-255]

Static route mapping destination IP address to next hop IP address
A.B.C.D/M Static route destination IP address field
A.B.C.D Next hop IP address
metric <0-255> Static route metric field in seconds

Command Mode:

Config

ip route bridge-route-aging-time

Use the

ip route bridge-route-aging-time

command to set the bridge route aging time. This command is functional in bridging

packet processing mode only.

Command Syntax

:

ip bridge-route-aging-time <10-1000000>

ip route default-gateway

Use the

ip default-gateway

to specify the default router or next hop where IP datagrams will be forwarded if no routes are found.

In Fast Forwarding mode, packets will be forwarded to the default Gateway on the Ethernet port if no host on the LAN responds.
This command is applicable in bridging, fast forwarding, and routing mode. In routing mode you can also specify a default
gateway by entering a static route with 0.0.0.0/0 as <nexthop>.

Command Syntax

:

ip default-gateway [enabled | disabled]
ip default-gateway A.B.C.D: Set default gateway IP address

A.B.C.D Gateway IP address

Command Mode:

Config

Example

ip route load-balancing

Use the

ip route load-balancing

to load balance traffic between two equal routes on two independent T1/E1 links.

Command Syntax

:

ip route load-balancing [ enabled | disabled]

Enable or disable load balancing. You will need to set two routes with equal cost to the same destination network on
different interface (NET1, NET2).

Command Mode:

Config

Example

ip route mode

Use the

ip route mode

to set packet processing mode to routing, bridging, or Fast Forwarding.

Command Syntax

:

ip route mode [routing | bridging | fast-forward ]

routing: In this mode packets will be routed to next hop address based on static and dynamic route tables.
bridging: Configures the unit for Bridging or VLAN bridging. This mode is commonly called MAC Bridging as the unit

forwards Ethernet frames.

fast-forward: In this mode the unit forwards IP packets, not the Ethernet frames, over the WAN link.

Command Mode:

Config

Example

«
...
157
158
159
160
161
...
»

Содержание LRU4240



























































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для LRU4240

Бренд: ZETR Страницы: 2

Бренд: CallDirect Страницы: 33

Бренд: Google Страницы: 14

Бренд: Klark Teknik Страницы: 50

SteelCentral NetExpress

Бренд: Riverbed Страницы: 38

Бренд: Radicom Страницы: 27

Бренд: Eneo Страницы: 68

Comet 3356P-LAN

Бренд: ZyXEL Communications Страницы: 38

Бренд: iNetVu Страницы: 20

Бренд: Idis Страницы: 18

Бренд: Axis Страницы: 64

Бренд: SHOWTEC Страницы: 15

Бренд: Geneko Страницы: 8

Бренд: Billion Страницы: 16

Бренд: TP-Link Страницы: 182

Бренд: Johnson Controls Страницы: 55

Бренд: Microview Страницы: 21

Бренд: Edimax Страницы: 33

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды