Black Box LRU4240 Скачать руководство пользователя страница 158 | Manualshive

Страница: 158 / 218

background image

146

SALES: 0870 90 10 750

Dual Trunk E1 Router User’s Guide

Dual Trunk E1 Router

Command Mode:

Config

Example

ip nat

Use the

ip nat

to enable or disable NAT for each physical interface.

Command Syntax

:

ip nat [enabled | disabled]

Global parameter enabling or disabling NATfeature.

ip nat IFNAME [nat | napt | two-way-nat] [enabled | disabled]

To specify and enable the type of nat per interface port.

Command Mode:

Config

Examples

Enable nat on NET1 port and disable NAT on Ethernet port and NET2.
Unit(config)#ip nat net1 enabled
Unit(config)#ip nat net2 disabled
Unit(config)#ip nat enet disabled
Unit(config)#ip nat enabled

ip nat global

Use the

ip nat global

to configure the

public IP addresses

(Global) used by NAT for the

private ip addresses

(local-addr).

Command Syntax

:

ip nat global A.B.C.D/M IFNAME

A.B.C.D/M: Global registered IP address with subnet mask
IFNAME the interface port [net1 | net2 | bundle0 | enet0] on which the global IP address is used

ip nat global clear: Clear the NAT global Map table

Command Mode:

Config

Example

ip nat local-addr

Use the

ip nat local-addr

to configure the networks that require NAT translation. Refer to Menu-$C Local address table for more

information.

Command Syntax

:

ip nat local-addr A.B.C.D/M IFNAME

A.B.C.D/M: Local IP Network and subnet to translate
IFNAME the interface port [net1 | net2 | bundle0 | enet0] to which the the local IP network is attached.

ip nat local-addr clear: Clear the local address table

Command Mode:

Config

Example

ip nat static

Use the

ip nat static

to configure static NAT one-to-one mapping of global IP address to local IP addresses.Static NAT

corresponds to menu-$JB NAT Static table.

Command Syntax

:

ip nat static A.B.C.D A.B.C.D IFNAME

A.B.C.D Local IP address to translate
A.B.C.D Translated IP address
IFNAME the [net1 | net2 | bundle0 | enet0] interface port

ip nat static clear: Clear Static NAT table

Command Mode:

Config

ip route

«
...
156
157
158
159
160
...
»

Содержание LRU4240



























































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для LRU4240

Бренд: Vanguard Страницы: 4

Бренд: Tripp Lite Страницы: 20

Nighthawk M6 Pro

Бренд: AT&T Страницы: 2

RIPWAVE 40-00460-00R

Бренд: Navini Networks Страницы: 35

Бренд: Teknim Страницы: 10

Бренд: UfiSpace Страницы: 35

Бренд: AMX Страницы: 2

Бренд: axing Страницы: 52

Media Board D/120JCT-LS-EW

Бренд: Dialogic Страницы: 2

Бренд: ICP DAS USA Страницы: 8

Бренд: Active Communications Страницы: 10

Бренд: ADDON Страницы: 4

Бренд: M-system Страницы: 4

Бренд: Kramer Страницы: 56

Бренд: Kasda Страницы: 39

Q-SYS QIO-GP8x8

Бренд: QSC Страницы: 13

Meridian 1 Option 11C Mini

Бренд: Meridian Страницы: 546

ForeFront 2616RC

Бренд: Patton electronics Страницы: 80

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды