Black Box LRU4240 Скачать руководство пользователя страница 3 | Manualshive

Страница: 3 / 218

background image

Copyright

Copyright © 1998, BLACK BOX Ltd

World copyright reserved. No part of this publication may be stored in a retrieval system,
transmitted, or reproduced in any way, including but not limited to photocopy, photograph,
magnetic, chemical, or other record, without the prior agreement and written permission of
BLACK BOX Ltd.

ISO Compliance

Warning

The Dual Trunk E1 Router complies with FCC Part 15 of the Federal Communications
Commission (FCC) Rules concerning radio frequency emissions for Class A computing
devices. The following section is required by the FCC.

Caution

In accordance with FCC Part 15 section 15.21, changes or modifications made by the buyer that
are not expressly approved by BLACK BOX Ltd could void the buyer’s authority to operate
this equipment.

This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause harmful interference to
radio communications. Operation of this equipment in a residential area is likely to cause
harmful interference in which case the user will be required to correct the interference at his
own expense.

This Class A digital device meets all requirementsof the Canadian Interference-Causing
Equipment Regulations.
Cet Appareil numerique de la classe A respecte toutes les exigences du Reglement sur le
materiel brouilleur du Canada.

Products Manufactured Under
An ISO 9001 Certified
Quality Management System

Dual Trunk E1 Router

Dual Trunk E1 Router User’s Guide

TECHNICAL: 0118 96 56 000

iii

«
1
2
3
4
5
...
»

Содержание LRU4240



























































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для LRU4240

Бренд: D-Link Страницы: 4

Бренд: D-Link Страницы: 2

Бренд: D-Link Страницы: 9

Бренд: D-Link Страницы: 8

Бренд: D-Link Страницы: 3

Бренд: D-Link Страницы: 28

Бренд: D-Link Страницы: 2

DSL-2540B - ADSL2/2+ Modem With EN Router

Бренд: D-Link Страницы: 12

Бренд: D-Link Страницы: 62

Бренд: 4RF Страницы: 7

Бренд: Abocom Страницы: 11

Бренд: Abocom Страницы: 19

Wisenet PRN-6400B4

Бренд: Hanwha Techwin Страницы: 14

Бренд: Ruckus Wireless Страницы: 2

Бренд: Rosewill Страницы: 10

Бренд: Freund Страницы: 6

PXI PXITM -1000

Бренд: National Instruments Страницы: 55

iMarc SLV 9820-2M

Бренд: Paradyne Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды