Black Box LRU4240 Скачать руководство пользователя страница 97 | Manualshive

Страница: 97 / 218

background image

Dual Trunk E1 Router

Dual Trunk E1 Router User’s Guide

TECHNICAL: 0118 96 56 000

85

Alarms

10

This chapter discusses alarm conditions and how these conditions are displayed.

C

ONFIGURING

A

LARM

C

ONDITIONS

When the Dual Trunk E1 Router detects an alarm condition, the unit reports the condition to the
terminal.

Depending on your network management environment, the unit may also send alarm messages or
SNMP trap messages.

Set alarm conditions in Menu-8A, Alarm Configuration.

The Dual Trunk E1 Router reports alarm conditions to the device connected to its COMM Port
(such as a terminal or modem)

SNMP traps are sent as configured in Menu-0B, SNMP Configuration; otherwise, the connection
indicated in Menu-8C identifies from where the alarms are reported.

If a modem is connected, the unit causes the modem to dial out (if in Menu 8C, Connection is set to
Modem; valid telephone numbers are set in Phone Number 1 or Phone Number 2; in Menu-8A.

Ethernet Signal Loss Alarm

is Enabled and Block all Alarms is set to No).

How Alarm Reports Are Displayed

Alarms are displayed on a terminal at the bottom of the screen when the terminal is connected to the
COMM Port and you are logged on:
Example—Ethernet Signal Loss Alarm will be given at the bottom of the screen, as follows:

??? ID: Oahu Data1 Carrier Loss Start: 07:17:37 Feb.22, 1997--

The alarm includes the unit ID, type of alarm, start or end of alarm condition, date, and time. The
alarm information remains on the screen either until a new alarm occurs or until you select a new
screen.

When no alarm is present, a dotted line (similar in appearance to the one below) is shown:

---------------------------------------------

When you are not logged on, the alarm appears as a single line showing the unit ID, type of alarm,
start or end of alarm, and the time stamp, if IP is disabled.

In SNMP mode, the system sends the alarm as an SNMP trap to the SNMP manager which displays
it on the SNMP console.

NOTE:

If IP is enabled, only SNMP traps are sent. Alarms will not be

displayed on the terminal.

«
...
95
96
97
98
99
...
»

Содержание LRU4240



























































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для LRU4240

DES-3526 - Switch - Stackable

Бренд: D-Link Страницы: 258

Бренд: IBM Страницы: 248

Бренд: B+B SmartWorx Страницы: 4

Бренд: Vivotek Страницы: 136

Бренд: Vonets Страницы: 8

Бренд: US Robotics Страницы: 36

Бренд: Watchguard Страницы: 40

WGR614 - Wireless-G Router Wireless

Бренд: NETGEAR Страницы: 116

Бренд: WAGO Страницы: 48

Бренд: AMX Страницы: 2

Бренд: SurfControl Страницы: 2

Бренд: NKE Страницы: 15

JetNet 3508-LVDC

Бренд: Korenix Страницы: 16

Бренд: Avaya Страницы: 73

Бренд: eWON Страницы: 34

Бренд: Supermicro Страницы: 15

Бренд: Softing Страницы: 16

GS2020E GigaSPIRE BLAST

Бренд: Calix Страницы: 15

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды