Bionaire BEF5000 - 2, Инструкция по эксплуатации, Страница: 4 / 44

4 5
OPERATING INSTRUCTIONS
• There may be an odor coming from the heater the first time you use
it. This is normal during the break-in period or after long term
storage. Make sure the heater is in a well ventilated area and
continue running it until the smell goes away.
• You may hear a popping or crackling sound as the heater heats up.
This is normal and safe operation.
• The Fireplace Heater can be operated by using the remote control
(Fig. 3) or the control panel (Fig. 2) located on the top of the unit.
• Place the heater on a firm, level surface or mount on wall.
• Avoid overloading your circuit by not using other high wattage
appliances in the same outlet.
POWER ON/OFF
1. Turn Main On/Off Switch to position (I) (see Fig.1 K)
2. Press the Power Button (L) the LCD Display (A) and Power Light (B)
will illuminate. The units default settings are: Temperature 80°F;
Timer OFF; Flame Brightness HIGH; Sound ON.
3. To completely switch heater off, turn Main On/Off Switch to
position (O) (See Fig.1 K)
Note: When turning the Power Button (L) OFF, the fan will continue to
run for 10 seconds to cool unit down. After all settings are chosen, LCD
Display (A) will go dark.
RESET INSTRUCTIONS
If the unit shuts down:
1. Turn mains On/Off Switch to position O (see Fig 1 K)
2. Turn MODE to OFF
3. Unplug unit, wait 30 minutes
4. Plug in the unit
5. Turn mains On/Off Switch to position I (see Fig 1 K)
6. Turn MODE to ON
THERMOSTAT
• Press Thermostat Button (M) until desired temperature level
appears on LCD Display (A). It is recommended to start by setting
the temperature to the highest setting. Note: the fan will continue to
run for flame operation without heat.
• The system now maintains the selected comfort level by automatically
turning the heater ON and OFF. The Thermostat cycles ON and OFF
with the heater element as it maintains the programmed temperature.
• When LCD Display (A) reads “00” the heat will turn off but the fan
will continue to run for flame operation and cooling.
TIMER
You can set the timer to automatically turn the unit off.
Press the Timer Button (N), select between 1 and 12 hours.
Your selection will then be displayed on the LCD Display (A).
FLAME BRIGHTNESS
There are four flame brightness settings: HIGH, MEDIUM, LOW, OFF.
Press Flame Brightness Button (O) to select desired brightness.
SOUND
Press Sound Button (P) to turn crackling sound ON or OFF.
Note: Sound will not work without flame operation on.
FAHRENHEIT/CELSIUS
Press to show temperature in Fahrenheit or Celsius.
CLEANING AND MAINTENANCE
• Always unplug the heater before cleaning and allow to cool.
• To clean glass use household glass cleaner.
• Lightly run a vacuum cleaner nozzle over the heater grill to remove
any dust or dirt that may have accumulated.
• Carefully wipe the heater with a soft, damp cloth. Please be very
cautious near the heating elements.
• NEVER use abrasive or flammable solvents to clean the heater.
• After cleaning, be sure to completely dry the heater with a cloth or
towel before switching on.
• Store your heater in a cool, dry location.
AUTO SAFETY SHUT OFF
This heater is equipped with, technologically advanced safety system
that automatically shuts off the current to the heater when a potential
overheat temperature is reached. The heater can only resume opera-
tion when you reset it and it has cooled down.
To Reset the Heater:
If your heater shuts down, follow these steps:
1. Unplug the heater and wait 30 minutes.
2. Plug in the heater, turn the power ON .
3. Your heater should now be operating properly.
TIP OVER PROTECTION
If the heater is knocked over, it will instantly shut off. To resume operation,
simply place the heater in an upright position.
BULB REPLACEMENT
Open doors marked (I) on back of unit with a cross head screwdriver
and replace bulb with a 25W or smaller threaded bulb.
TROUBLESHOOTING
Flame not bright enough
1. Regulate flame brightness using the Flame Brightness button.
2. Check both bulbs are working and replace if necessary.
Simulated fire will not illuminate
1. Check power.
2. Press Flame Button .
3. Check both bulbs and replace if necessary.
Unit making crackling/popping sound
1. Unit is intended to replicate the gentle popping and crackling
sounds of a residential fireplace.
2. Press Sound button to turn off and on sound.
Heat will not turn off
1. Refer to operating instructions.
2. Press Thermostat button until 00 is displayed. The fan will
continue to run for flame operation.
Heater blows cool air
1. This is normal in order to cool down the heater and preserve the
heating element.
2. This is normal when the heat is turned off.
Remote does not work
1. Change batteries (See Assembly Instructions).
2. Be sure to point Remote at Control Panel on unit.
3. Be sure there are no obstructions between remote and unit.
4. Make sure glass over LCD Display is clean.
Not enough heat
1. Increase thermostat setting to highest setting.
2. This is a 2000 watt heater and is intended for supplement heat only.
Heater cycles on and off frequently
1. The thermostat automatically turns the heater on and off to maintain
selected comfort level.
2. To make this occur less frequently adjust the thermostat setting up or down.
FITTING A REPLACEMENT PLUG FOR U.K. AND
IRELAND ONLY
If the plug is not suitable for the socket outlets in your home, it can be
removed and replaced by a plug of the correct type. Please refer to "In-
stallation of a plug" below.
BEF5000-I_IB.qxd:Layout 2 7/10/08 12:35 PM Page 4
All manuals and user guides at all-guides.com