manualshive.com logo in svg

BIO RAD PTC-0240, Руководство по эксплуатации

Поделиться
Скачать
BIO RAD PTC-0240 Скачать руководство пользователя страница 114

Troubleshooting

Tech Support: 1-800-4BIORAD • 1-800-424-6723 • www.bio-rad.com 

10-5

Remote

Error Code

Error Code

Reason

Action

7

IFF

The internal fan is not providing
adequate cooling for the instru-
ment.

Call (800) 4BIORAD (in the US or
Canada), or your local distributor
(outside the US or Canada).

22

LSF

An irregularity has been detected
in a heated lid sensor. The heated
lid has been temporarily turned
off. The sensor will be checked
and you will be notified if any
problem is found.

No action required at this time.

None

LRPI

An imbalance has been detected
in the sample block. There may be
a problem with a Peltier module.

Call (800) 4BIORAD (in the US or
Canada), or your local distributor
(outside the US or Canada).

None

MC

A memory fault has been found.
Stored programs may be affected.

Call (800) 4BIORAD (in the US or
Canada), or your local distributor
(outside the US or Canada).

None

NMA

All available memory has been
filled.

Please delete unused programs,
or call (800) 4BIORAD (in the US
or Canada), or your local distrib-
utor (outside the US or Canada).

18

PSF

A possible fault was detected in
the in-sample probe. The thermal
control method has been
switched to Calculated Mode.
Results may have been affected.

Check probe and connections. 
If problem reoccurs, please call
(800) 4BIORAD (in the US or
Canada), or your local distributor
(outside the US or Canada).

9

PSO-CAF

The power supplytemperature is
somewhat higher than normal.
The power supply sensor will be
checked and you will be notified
if any problem is found.

Please observet he following
guidelines: 1) place instruments at
least 10 cm apart, 2) avoid
placing instruments in any loca-
tion where hot air might enter the
intake vents, 3) place instruments
on a hard surface with no debris
or paper underneath, 4) clean all
air vents and Alpha unit fins of
dust and debris, 5) avoid running
the instrument in areas with
ambient temperatures above
25°C. Continue to use the instru-
ment. If problem reoccurs please
call (800) 4BIORAD (in the US or
Canada), or your local distributor
(outside the US or Canada).

Содержание PTC-0240





















































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды