EN
77-3110-R1.3 (4/2016)
3 / 14
In this part sheet, the words
WARNING
,
CAUTION
and
NOTE
are used to
emphasize important safety information as follows:
Hazards or unsafe practices which
could result in minor personal injury,
product or property damage.
!
CAUTION
Hazards or unsafe practices which
could result in severe personal
injury, death or substantial property
damage.
!
WARNING
Important installation, operation or
maintenance information.
NOTE
The following hazards may occur during the normal use of this equipment. Please read the following chart.
!
WARNING
HAZARD
CAUSE
SAFEGUARDS
EXPLOSION
STATIC ELECTRICITY
Use of this equipment in a
potentially explosive atmosphere.
Vapours from flammable liquids can
catch fire or explode from static
electricity discharges.
1. If installing this equipment in a potentially explosive atmosphere,
check the ATEX equipment category and temperature ratings meet
the requirements for the zoned area.
2. Check electrical continuity of the air supply to earth—should be no
greater than 106 Ω.
3. Electrically bond all metallic equipment to earth. Should be no greater
than 1 Ω.
INHALING TOXIC
SUBSTANCES
Certain materials may be harmful
if inhaled, or there is contact with
the skin.
1. Follow the requirements of the Safety Data Sheet supplied by the
coating manufacturer.
2. Adequate exhaust must be provided to keep the air free of
accumulations of toxic materials.
3. Use a mask or respirator wherever there is a risk of inhaling sprayed
materials.
GENERAL SAFETY
Air stream from product may
contain solid or liquid material that
can result in eye injury.
Sound level from air motors may
exceed 80 dba.
Improper operation or maintenance
may create a hazard.
1. Wear eye protection when using this equipment.
2. Wearing of ear protection is recommended.
3. Operators should be given adequate training in the safe use and
maintenance of this equipment. Refer to Pressure Systems Safety
Regulations 2000 Approved Code of Practice.
SPECIAL
CONDITIONS
FOR SAFE USE
REQUIRED BY ATEX
CERTIFICATION
Over pressurization of equipment
can cause equipment failure or
injury.
Use lubricating medium resistant to
carburisation.
Improper operation or maintenance
may create a hazard.
1. Do not exceed the stated maximum working pressures and motor
speed as specified on page 4.
2. Only a suitably approved static dissipating or conductive air supply
hoses shall be attached to the equipment and terminated to the air
supply.
3. Air supplies (compressors etc) shall be sited in a non-hazardous area
with a filter on the air intake system to prevent the ingress of dust or
similar foreign material into the parts where compression takes place.
4. Use lubricating medium resistant to carburisation and has an auto
ignition temperature of more than 185ºC for T4 equipment.
5. User shall verify the presence of gearbox lubricant (QS-5012-1-CE
only) in accordance with the instructions on page 5, before operating
the air motor.
6. User shall ensure all metallic parts of the equipment are suitably
bonded to earth. Should be no greater than 1 Ω.
7. QS-5012-1-CE should only be installed onto a vertical agitator shaft
assembly.
NEVER MODIFY THE
EQUIPMENT
Improper operation or maintenance
may create a hazard.
Do not modify the equipment unless the manufacturer provides written
approval.
Binks reserves the right to modify equipment specification without prior notice.
IT IS THE RESPONSIBILITY OF THE EMPLOYER TO PROVIDE THIS INFORMATION TO THE OPERATOR OF THE EQUIPMENT.
FOR FURTHER SAFETY INFORMATION REGARDING THIS EQUIPMENT, SEE THE GENERAL EQUIPMENT SAFETY BOOKLET (77-5300).
Содержание PT-418-CE
