background image

62

62

DIMENSIONS ARE IN MM

5

4

3

1

2

REVISION

REV

DESCRIPTION

DATE

EDITED BY

ECO#

F

UPDATED BOM REVISION

07/14/2010

TM

00380

G

UPDATED BOM REVISIONS

08/13/2010

AC

00388

H

UPDATED BOM REVISIONS

09/14/2010

TM

00396

ITEM NO

PART NUMBER

DESCRIPTION

QTY

REV

1

5245134

XPR-10CX LIFT SUPERSTRUCTURE

1

H

2

5250140

XPR-10CX EXTENDED PARTS BOX

1

F

3

5215195

XPR-9/10C/CX LOW PROFILE MEDIUM ARM 

ASSEMBLY

2

C

4

5210741

XPR-9FX/FDX/FSX/ 10ACX/10CX LOW PROFILE 

TRIPLE TELESCOPING ARM ASSEMBLY

2

C

5

5210269

XPR-7TR/10 POST EXTENSION WELDMENT

2

B

 SHEET 1 OF 2

REV

DWG.  NO.

A

SIZE

TITLE:

NAME

DATE

CHECKED

DRAWN

SIZE:

MATERIAL:

H

1645 LEMONWOOD DR. SANTA PAULA, CA 93060

              

PROPRIETARY AND CONFIDENTIAL

THE INFORMATION CONTAINED IN THIS DRAWING IS  THE SOLE PROPERTY OF 

BENDPAK INC.

 ANY 

REPRODUCTION IN PART OR AS A WHOLE WITHOUT  THE WRITTEN PERMISSION OF 

BENDPAK INC.

 IS 

PROHIBITED.

NOTE: UNLESS OTHERWISE SPECIFIED

.

TM

5260063

XPR-10CX EXTENDED 

RECEIVED LIFT

---

---

01/26/2010

DO NOT SCALE DRAWING

1:30

SCALE:

THIRD ANGLE PROJECTION

AC

09/20/2010

SEE SHIPPING INSTRUCTIONS FOR FINAL PACKAGING

1.

Содержание XpR-10AC-168













































































Отзывы: