BendPak XpR-10AC-168 Скачать руководство пользователя страница 15

Страница: 15 / 76

StEP 5

(Installing The POWERSIDE Column)

1. Before proceeding, double the check measurements

and make certain that the bases of each Column are

aligned with the chalk line.

2. Using the base plate on the POWERSIDE column as a

guide, drill each anchor hole in the concrete (approximately

4” deep for 10K models and 6” deep for 12K and15K;

8” for 18K models) using a rotary hammer drill and 3/4”

concrete drill-bit. To assure full holding power, do not ream

the hole or allow the drill to wobble. (See Fig. 5.1)

3. After drilling, remove dust thoroughly from each hole

making certain that the Column remains aligned with the

chalk line.

4. Assemble the washers and nuts on the anchors

then tap into each hole with a hammer until the washer

rests against the Base Plate. Be sure that if shimming is

required that enough threads are left exposed.

(See Fig. 5.2)

5. If shimming is required, insert the shims as necessary

under the Base Plate so that when the anchor bolts are

tightened, the Columns will be plumb. (See Fig. 5.3)

6. If installing the Optional Foot Guards, place foot guards

on left and right side as shown. (See Fig 5.4)

7. With the Foot Guards, shims and anchor bolts in place,

tighten by securing the nut to the base then turning 3-5 full

turns clockwise.

Do Not

use an impact wrench for this

procedure. (See Fig. 5.5)

Fig 5.1

Fig 5.2

Fig 5.3

NotE:

To ease installation of the Top Trough, it helps to keep

the anchor bolts loose on one of the Columns until the

Top Trough is mounted.

Fig 5.4

Fig 5.5

IMPoRtANt NotE:

BendPak lifts are supplied with installation

instructions and concrete fasteners meeting the

criteria as prescribed by the American National

Standard "Automotive Lifts - Safety Requirements for

Construction, testing, and Validation" ANSI/ALI

ALCtV-2006. Lift buyers are responsible for any

special regional structural and/or seismic anchoring

requirements specified by any other agencies and/or

codes such as the Uniform Building Code (UBC)

and/or International Building Code (IBC).

Содержание XpR-10AC-168













































































Результаты поиска

Содержание XpR-10AC-168

Отзывы:

Похожие инструкции для XpR-10AC-168

Бренды по названию

Популярные бренды

BendPak XpR-10AC-168, Инструкция по установке и эксплуатации

Результаты поиска

Содержание XpR-10AC-168

Отзывы:

Похожие инструкции для XpR-10AC-168

Бренды по названию

Популярные бренды