BendPak XpR-10AC-168 Скачать руководство пользователя страница 19

Страница: 19 / 76

4. Route the Cable through the Top Trough Safety Cable

Pulley(s) and across the lift. (See Figs 9.5 & 9.6)

5. Route the Cable the same way on the Powerside

going back down the Column.

6. Route the Cable over the top pin on the Safety Handle.

Insert the Cable end through the hole on the Threaded

Post. (See Fig 9.7)

7. Pull the slack out the Safety Cable and hold tension

as the Cable is being tightened. Tighten jam nuts on

either side of the Cable to secure it into place.

(See Fig 9.7)

StEP 10

(Installing Hydraulic Lines)

1. Install the Bulkhead Tee Fitting into the Powerside

Column. The through hole is located approximately 90

inches from the floor on the back wall of the Powerside

Column.

2. Connect the

Powerside

Cylinder Hose to the tee fitting

Be sure to route the hose through the retainer rings inside

the columns.

3. Route the

offside

Cylinder Hose (Crossover Hose) up

through the Column and across the Top Trough, down the

Column and connect it to the Bulkhead Tee Fitting.

(See Fig 10.1)

NotE:

ake sure to tighten both nuts equally so as to

keep the Safety Cable centered

Fig 9.6

Fig 9.7

Fig 10.1

Fig 9.5

Содержание XpR-10AC-168













































































Результаты поиска

Содержание XpR-10AC-168

Отзывы:

Похожие инструкции для XpR-10AC-168

Бренды по названию

Популярные бренды

BendPak XpR-10AC-168, Инструкция по установке и эксплуатации

Результаты поиска

Содержание XpR-10AC-168

Отзывы:

Похожие инструкции для XpR-10AC-168

Бренды по названию

Популярные бренды