BendPak XpR-10AC-168 Скачать руководство пользователя страница 8

Страница: 8 / 76

1. Carefully remove the crating and packing
materials.

CAutIoN!

Be careful when cutting steel

banding material as items may become loose and fall
causing personal harm or injury.

2. Check the voltage, phase and proper amperage
requirements for the motor shown on the motor plate.
Wiring should be performed by a certified electrician only.

IMPoRtANt SAFEty INStRuCtIoNS !

Read these safety instructions entirely!

IMPoRtANt NotICE !

Do not attempt to install this lift if you have never been trained on basic automotive lift installation procedures.

Never attempt to lift components without proper lifting tools such as forklift or cranes.

Stay clear of any moving parts that can fall and cause injury.

INtRoDuCtIoN

READ AND uNDERStAND

all safety warning proce-

dures before operating lift.

KEEP HANDS AND FEEt CLEAR

. Remove hands and

feet from any moving parts. Keep feet clear of lift when lower-

ing. Avoid pinch points.

KEEP WoRK AREA CLEAN

. Cluttered work areas

invite injuries.

4. Consider work area environment. Do not expose equip-

ment to rain.

Do Not

use in damp or wet locations. Keep

area well lighted.

oNLy tRAINED oPERAtoRS

should operate this lift.

All non-trained personnel should be kept away from work

area. Never let

non-trained personnel come in contact with,

or operate lift.

uSE LIFt CoRRECtLy

. Use lift in the proper manner.

Never use lifting adapters other than what is approved by the

manufacturer.

Do Not

override self-closing lift controls.

REMAIN CLEAR

of lift when raising or lowering vehicle.

CLEAR AREA

if vehicle is in danger of falling.

10.

ALWAyS ENSuRE

that the safeties are engaged before

any attempt is made to work on or near vehicle.

11.

DRESS PRoPERLy

. Non-skid steel-toe footwear is

recommended when operating lift.

12.

GuARD AGAINSt ELECtRIC SHoCK

. This lift must be

grounded while in use to protect the operator

from electric shock. Never connect the green

power cord wire to a live terminal. This is for

ground only.

13.

DANGER!

The power unit used on this lift contains high

voltage. Disconnect power at the receptacle

before performing any electrical repairs.

Secure plug so that it cannot be accidentally

plugged in during service.

14.

WARNING! RISK oF EXPLoSIoN

. This equipment

has internal arcing or sparking parts which

should not be exposed to flammable vapors.

This machine should not be located in a

recessed area or below floor level.

15.

MAINtAIN WItH CARE

. Keep lift clean for better and

safer performance. Follow manual for proper lubrication

and maintenance instructions. Keep control handles and/or

buttons dry, clean and free from grease and oil.

16.

StAy ALERt

. Watch what you are doing. Use common

sense. Be aware.

17.

CHECK FoR DAMAGED PARtS

. Check for alignment

of moving parts, breakage of parts or any condition that may

affect its operation. Do not use lift if any component is broken

or damaged.

18.

NEVER

remove safety related components from the lift.

Do not use lift if safety related components are damaged

or missing.

19. Keep hair, loose clothing, fingers, and all parts of body

away from moving parts

20. Use only as described in this manual. Use only manu-

facturer’s recommended attachments

21.

ALWAyS WEAR SAFEty GLASSES.

Everyday eye-

glasses only have impact resistant lenses, they are not

safety glasses

22.

SAVE tHESE INStRuCtIoNS.

Содержание XpR-10AC-168













































































Результаты поиска

Содержание XpR-10AC-168

Отзывы:

Похожие инструкции для XpR-10AC-168

Бренды по названию

Популярные бренды

BendPak XpR-10AC-168, Инструкция по установке и эксплуатации

Результаты поиска

Содержание XpR-10AC-168

Отзывы:

Похожие инструкции для XpR-10AC-168

Бренды по названию

Популярные бренды