BendPak XpR-10AC-168 Скачать руководство пользователя страница 36

Страница: 36 / 76

to RAISE tHE LIFt

1. Before Loading: Lift must be fully lowered and service

bay clear of all personnel before the vehicle is brought on

lift with the swing arms set to the full drive-thru position.

2. Loading: Swing arms under vehicle and position

adapters at vehicle manufacturer’s recommended lift

points. Use height extenders or optional frame-cradle

adapters when necessary to ensure good contact.

(See Fig 19.2-3)

3. Some vehicles may have the manufacturer's Service

Garage Lift Point locations identified by triangle shape

marks on the undercarriage (reference ANSI/SAE j2184-

1992). Also, there may be a label located on the right front

door jamb area showing specific vehicle lift points.

tyPICAL LIFtING PoINtS

4. Position vehicle for proper weight distribution arms

under vehicle to allow adapters to contact at the

manufacturer’s recommended pick up points.

WARNING!

To avoid personal injury and/or property damage, permit

only trained personnel to operate lift. After reviewing

these instructions, get familiar with lift controls by

running the lift through a few cycles before loading

vehicle on lift. Always lift the vehicle using all four

adapters.

NEVER

raise just one end, one corner,

or one side of vehicle.

WARNING!

Many specialty or modified vehicles cannot be raised

on a two-post frame engaging lift. Contact vehicle

manufacturer for raising or jacking details.

Fig. 19.2

Fig. 19.3

Содержание XpR-10AC-168













































































Результаты поиска

Содержание XpR-10AC-168

Отзывы:

Похожие инструкции для XpR-10AC-168

Бренды по названию

Популярные бренды

BendPak XpR-10AC-168, Инструкция по установке и эксплуатации

Результаты поиска

Содержание XpR-10AC-168

Отзывы:

Похожие инструкции для XpR-10AC-168

Бренды по названию

Популярные бренды