BendPak XpR-10AC-168 Скачать руководство пользователя страница 61

Страница: 61 / 76

DIMENSIONS ARE IN MM

REVISION

REV

DESCRIPTION

DATE

EDITED BY

ECO#

UPDATED BOM REVISION

06/30/2010

00377

UPDATED BOM REVISIONS

07/14/2010

00380

UPDATED BOM REVISIONS

08/13/2010

00388

NEXT ASSEMBLY

5260062

ITEM NO

PART

NUMBER

DESCRIPTION

QTY

REV

5174218

XPR-10/12C/15/18C EXTENDED PARTS BAG

5505116

MX-10, XPR-7/9/10 LIFT HEAD PIN WELDMENT

5595109

XPR-10C EXTENDED CABLE ASSY Ø10 x 10249mm ST

5570832

XP/XPR/MX HYDRAULIC HOSE ASSY Ø6.35 x 2299mm SB

5570017

XP/XPR HYDRAULIC HOSE ASSY Ø10 x 1219mm SB

5595466

XPR-10C EXTENDED Ø2.4 X 8509 SAFETY CABLE

5570005

XP/XPR-10C/AC EXTENDED HYDRAULIC HOSE ASSY Ø6.35

x 9258 SB

5210007

XP/XPR POWER SIDE SAFEY ASSEMBLY

5210010

XP/XPR OFF SIDE SAFETY WELDMENT

5715003

POWER UNIT VIBRATION DAMPENER

5215250

MD-6XP, ALL XP/XPR SLIP ON LIFT PAD ASSEMBLY

5730663

XP/XPR-9/10, XPR-7 POST ASSEMBLY LIFT HEAD FOOT

GUARD R.H.

5730664

XP/XPR-9/10, XPR-7 POST ASSEMBLY LIFT HEAD FOOT

GUARD L.H.

5736171

MX, XPR-9/10 BOLT ON ARM RESTRAINT GEAR

5600163

XPR-7TR/10/12C/15/18C POWER SIDE SAFETY COVER

5210009

XP/XPR-7TR/7TRFD/ 9FD/9FDX/10/12/12FD/15/18C OFF

SIDE SAFETY COVER

5746390

XP/XPR/RJ/MX/MD-6XP SHORT LIFT PAD EXTENSION

(113mm LG.)

5746395

MX/XP/XPR LONG LIFT PAD EXTENSION (182mm LG.)

5545342

WASHER M18 FLAT

5535358

NUT M18 x 2.5 NL

5540129

E RING Ø38mm OD

5746167

DOUBLE THREADED ROD M10 x 1.5 x 275

5700400

MX/XP/XPR MICROSWITCH COVER PLATE

SHEET 1 OF 1

REV

DWG. NO.

SIZE

TITLE:

NAME

DATE

CHECKED

DRAWN

SIZE:

MATERIAL:

1645 LEMONWOOD DR. SANTA PAULA, CA 93060

PROPRIETARY AND CONFIDENTIAL

THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF

BENDPAK INC.

ANY

REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF

BENDPAK INC.

PROHIBITED.

5250139

XPR-10C-EXTENDED

PARTS BOX

---

01/22/2010

DO NOT SCALE DRAWING

1:30

SCALE:

THIRD ANGLE PROJECTION

08/19/2010

SEE SHIPPING INSTRUCTIONS FOR FINAL PACKAGING

INSERT PARTS BAG INTO PARTS BOX FOR SHIPMENT

THREAD 5535358 WITH 5545342 ONTO CABLES FOR SHIPMENT

HOSES AND CABLES IN REPRESENTATIONAL FORM

NOTE: UNLESS OTHERWISE SPECIFIED

Содержание XpR-10AC-168













































































Результаты поиска

Содержание XpR-10AC-168

Отзывы:

Похожие инструкции для XpR-10AC-168

Бренды по названию

Популярные бренды

BendPak XpR-10AC-168, Инструкция по установке и эксплуатации

Результаты поиска

Содержание XpR-10AC-168

Отзывы:

Похожие инструкции для XpR-10AC-168

Бренды по названию

Популярные бренды