manualshive.com logo in svg

BendPak XpR-10AC-168, Инструкция по установке и эксплуатации

Установочное руководство по эксплуатации BendPak XpR-10AC-168 доступно для скачивания бесплатно на нашем сайте. Это обязательное пособие поможет вам правильно установить и настроить ваш продукт для оптимальной работы. Скачайте его прямо сейчас с нашего сайта.

Поделиться
Скачать
background image

77

INStALLER / oPERAtoR

PLEASE READ AND FuLLy 

uNDERStAND. 

By PRoCEEDING you AGREE to 

tHE FoLLoWING.

t 

I have visually inspected the site where the lift is to 

be installed and verified the concrete to be in good condi-

tion and free of cracks or other defects. I understand that 

installing a lift on cracked or defective concrete could 

cause lift failure resulting in personal injury or death.

t 

I understand that a level floor is required for proper 

installation and level lifting. 

t 

I understand that I am responsible if my floor is of 

questionable slope and that I will be responsible for all 

charges related to pouring a new level concrete slab if 

required and any charges.

t

   I understand that Bendpak lifts are supplied with 

concrete fasteners meeting the criteria of the American 

National Standard “Automotive Lifts - Safety Requirements 

for Construction, Testing, and Validation” ANSI/ALI 

ALCTV-2006, and that I will be responsible for all charges 

related to any special regional structural and/or seismic 

anchoring requirements specified by any other agencies 

and/or codes such as the Uniform Building Code (UBC) 

and/or International Building Code (IBC).

t 

I will assume full responsibility for the concrete floor 

and condition thereof, now or later, where the above 

equipment model(s) are to be installed. Failure to follow 

danger, warning, and caution instructions may lead to 

serious personal injury or death to operator or bystander 

or damage to property. 

t 

I understand that BendPak lifts are designed to be 

installed in indoor locations only. Failure to follow instal-

lation instructions may lead to serious personal injury or 

death to operator or bystander or damage

 

to property or 

lift.

Failure to follow danger, warning, and caution        

instructions may lead to serious personal injury or death 

to operator or bystander or damage to property. 

Please read entire manual prior to installation. Do not 

operate this machine until you read and understand 

all the dangers, warnings and cautions in this manual. 

For additional copies or further information, contact:

BendPak Inc. / Ranger Products

1645 Lemonwood Dr.

Santa Paula, CA. 93060 

1-805-933-9970

www.bendpak.com

INStALLER / oPERAtoR

PRotECtIVE EQuIPMENt

Personal protective equipment helps makes installation 
and operation safer, however, it does not take the place 
of safe operating practices. Always wear durable work   
clothing during any installation and/or service activity. 
Shop aprons or shop coats may also be worn, however 
loose  fitting clothing should be avoided. Tight fitting leath-
er gloves are  recommended to protect technician hands 
when handling parts. Sturdy leather work shoes with steel 
toes and oil resistant soles should be used by all service 
personnel to help prevent injury during typical installation 
and operation activities. 
Eye protection is essential during installa-
tion and operation activities. Safety glasses 
with side shields, goggles, or face shields 
are acceptable. Everyday eyeglasses only 
have impact resistant lenses, they are not 
safety glasses. Back belts provide support 
during lifting activities and are also helpful in providing 
worker protection. Consideration should also be given 
to the use of hearing protection if  service activity is per-
formed in an enclosed area, or if noise levels are high.

tHIS SyMBoL PoINtS out IMPoRtANt SAFEty INStRuCtIoNS WHICH IF Not FoLLoWED

CouLD ENDANGER tHE PERSoNAL SAFEty AND/oR PRoPERty oR youRSELF AND otHERS

AND CAN CAuSE PERSoNAL INJuRy oR DEAtH.  READ AND FoLLoW ALL INStRuCtIoNS IN

tHIS MANuAL BEFoRE AttEMPtING to oPERAtE tHIS MACHINE.

Содержание XpR-10AC-168













































































Отзывы:

Нет отзывов

Похожие инструкции для XpR-10AC-168

Vectaire Studio Installation, Operating And Maintenance Instructions preview
Studio
Бренд: Vectaire Страницы: 2
Truweld Equipment TWE - SC2402 Operation Manual preview
TWE - SC2402
Бренд: Truweld Equipment Страницы: 28
TradeQuip 2056T Owner'S Manual preview
2056T
Бренд: TradeQuip Страницы: 9
Omron Sysmac NX-TBX01 User Manual preview
Sysmac NX-TBX01
Бренд: Omron Страницы: 172
DOLD 0056632 Operating Instructions Manual preview
0056632
Бренд: DOLD Страницы: 20
Miller Electric RCT-224 Trailer Owner'S Manual preview
RCT-224 Trailer
Бренд: Miller Electric Страницы: 24
Weldability MIG160T Instruction Manual preview
MIG160T
Бренд: Weldability Страницы: 12
VAT Series 651 Installation, Operating, & Maintenance Instructions preview
Series 651
Бренд: VAT Страницы: 53
ESAB Caddy Tig 1500i TA34 Service Manual preview
Caddy Tig 1500i TA34
Бренд: ESAB Страницы: 50
Zepro ZHD-1500-MA-DA Installation Instruction preview
ZHD-1500-MA-DA
Бренд: Zepro Страницы: 6
Zephir 2200 Traditional Series Quick Start Manual preview
2200 Traditional Series
Бренд: Zephir Страницы: 2
CarlStahl RZ150 User Information preview
RZ150
Бренд: CarlStahl Страницы: 28
Oshkosh Corporation JLG 15BD Illustrated Parts Manual preview
JLG 15BD
Бренд: Oshkosh Corporation Страницы: 92
Fetco CBS-5000H Series Users Manual And Operator Instructions preview
CBS-5000H Series
Бренд: Fetco Страницы: 22
Maxon 297072-01 Instruction preview
297072-01
Бренд: Maxon Страницы: 3
DriSteem VAPOR-LOGIC 3 Conversion Instructions preview
VAPOR-LOGIC 3
Бренд: DriSteem Страницы: 4
ICP DAS USA DIO-96/144 Quick Start Manual preview
DIO-96/144
Бренд: ICP DAS USA Страницы: 8
Panasonic VL-W1-N Series Setup And Maintenance Manual preview
VL-W1-N Series
Бренд: Panasonic Страницы: 176

Бренды по названию

Популярные бренды

Загрузить еще бренды