VAT Series 651 Скачать руководство пользователя

Страница: 1 / 53

Installation, Operating & Maintenance Instructions

Series 651 DN 320-400 (I.D. 12“ - 16”), Logic

VAT Vakuumventile AG, CH-9469 Haag, Switzerland

Tel +41 81 771 61 61 Fax +41 81 771 48 30 [email protected] www.vatvalve.com

267736ED

2008-02-26

1/53

Pendulum control & isolation valve

with extended control range
with Logic interface

This manual is valid for the valve ordering number(s):

651 . . - . . GC - . . . .

(1 sensor input)

651 . . - . . GE - . . . .

(2 sensor inputs)

651 . . - . . AC - . . . .

(1 sensor input /

15V SPS)

651 . . - . . AE - . . . .

(2 sensor inputs /

15V SPS)

651 . . - . . HC - . . . .

(1 sensor input / PFO)

651 . . - . . HE - . . . .

(2 sensor inputs / PFO)

651 . . - . . CC - . . . .

(1 sensor input /

15V SPS / PFO)

651 . . - . . CE - . . . .

(2 sensor inputs /

15V SPS / PFO)

SPS = Sensor Power Supply

PFO = Power Failure Option

configured with firmware

651P.1E.05

The fabrication number is indicated on each product as per the label
below (or similar):

made in Switzerland
Fabrication No.:

patented

. .

651 . . – . . . . – . . . . / . . . .

A – . . . . . .

Fabrication number

sample picture

Explanation of symbols:

Read declaration carefully before you start any other
action!

Keep body parts and objects away from the valve
opening!

Attention!

Hot surfaces; do not touch!

Product is in conformity with EC guidelines,
if applicable!

Loaded springs and/or air cushions are potential
hazards!

Disconnect electrical power and compressed air
lines. Do not touch parts under voltage!

Wear gloves!

Read these «Installation, Operating & Maintenance Instructions» and the enclosed «General
Safety Instructions» carefully before you start any other action!

Содержание Series 651






















































Результаты поиска

Содержание Series 651

Отзывы:

Похожие инструкции для Series 651

Бренды по названию

Популярные бренды

VAT Series 651, Инструкции по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание Series 651

Отзывы:

Похожие инструкции для Series 651

Бренды по названию

Популярные бренды