VAT Series 651 Скачать руководство пользователя | Manualshive

Страница: 34 / 53

background image

Installation, Operating & Maintenance Instructions

Series 651 DN 320-400 (I.D. 12“ - 16”), Logic

VAT Vakuumventile AG, CH-9469 Haag, Switzerland

Tel +41 81 771 61 61 Fax +41 81 771 48 30 [email protected] www.vatvalve.com

267736ED

2008-02-26

34/53

3.11.4 Analog inputs and outputs

Pin

Function

Signal type Description

25

SETPOINT

Analog

input

1)

The meaning of the setpoint input depends on the operation mode.

LEARN:
A voltage of 0-10V shall be applied to this input as pressure limit for learn.
The limit pressure is in linear relation to the applied voltage. 10V relates to
sensor full scale.
In case of 2 sensor operation 10V relates to sensor 1 full scale (high
range).

Note: To activate pressure limit function for remote operation it must be
configured accordingly. Refer to «Interface configuration»

PRESSURE CONTROL:
A voltage of 0-10V shall be applied to this input as pressure setpoint. The
pressure setpoint is in linear relation to the applied voltage. Depending on
selected SETPOINT RANGE 10V means either sensor full scale or 10%
of sensor full scale.
In case of 2 sensor operation 10V relates to sensor 1 full scale (high
range).

POSITION CONTROL:
A voltage of 0-10V shall be applied to this input as position setpoint. The
position setpoint is in linear relation to the applied voltage. 0V is closed
but not isolation function and 10V is open position.
(Use digital input for isolation function)

12

PRESSURE

Analog

output

1)

This output indicates the current pressure as 0-10V. The output voltage is
in linear relation to the pressure. Depending on the selected SETPOINT
RANGE 10V means either sensor full scale or 10% of sensor full scale.
In case of 2 sensor operation sensor full scale relates to sensor 1 (high
range).

11

POSITION

Analog

output

1)

This output indicates the current valve position as 0-10V voltage range.
The voltage is in linear relation to the valve position. 0V is closed but not
isolation function and 10V is open position.
(Use digital output for isolation function)

13

ANALOG GROUND

Analog
ground

Ground for analog input and analog outputs.

1

CHASSIS GROUND

Chassis

ground

Chassis ground connected to case. Shall be used to connect cable shield.

1) Refer to «Function and wiring» for details about input / output circuit.

«
...
32
33
34
35
36
...
»

Содержание Series 651






















































Отзывы:

Нет отзывов

Похожие инструкции для Series 651

Бренд: Farris Engineering Страницы: 12

Бренд: Eastern Times Technology Страницы: 4

Бренд: Vacon Страницы: 18

Бренд: Bang & Olufsen Страницы: 36

Бренд: Mad Catz Страницы: 4

Бренд: Garmin Страницы: 4

Бренд: Magellan Страницы: 2

Бренд: olympia electronics Страницы: 10

Бренд: Watts Страницы: 24

Бренд: Ban Seok Страницы: 9

Бренд: DSE Страницы: 2

Бренд: KanDao Страницы: 265

Бренд: WAGNER Страницы: 128

Бренд: HEIDENHAIN Страницы: 257

Бренд: GSD Страницы: 5

Бренд: L&L Страницы: 16

Бренд: Castex Страницы: 23

Бренд: Mitsubishi Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды