VAT Series 651 Скачать руководство пользователя | Manualshive

Страница: 20 / 53

background image

Installation, Operating & Maintenance Instructions

Series 651 DN 320-400 (I.D. 12“ - 16”), Logic

VAT Vakuumventile AG, CH-9469 Haag, Switzerland

Tel +41 81 771 61 61 Fax +41 81 771 48 30 [email protected] www.vatvalve.com

267736ED

2008-02-26

20/53

3.6.2 Valve and sensor configuration

Basic valve configuration must be adapted according to application needs.

•

Definition of valve plate position (CLOSE or OPEN) after power up sequence. Default is ‘close‘.

•

Definition of valve plate position (CLOSE or OPEN) in case of a power failure. Default is ‘not defined‘.

Only for versions that have Power Fail Option equipped [651 . . - . . C . - . . . . or 651 . . - . . H . - . . . . ].

•

ZERO function. This may be ‘disabled’ or ‘enabled’. Default is ‘enabled‘. Refer also to «ZERO».

•

Sensor configuration for 2 sensor version [651 . . - . . . E - . . . .].

Refer also to «Pressure control operation with 2 sensors».

Local operation

:

(‘Control View’, ‘Control Performance Analyzer’ or

‘Service Box 2‘)

Remote operation

:

1. Do power up configuration in menu

‘Setup / Valve’.

2. Do power fail configuration in menu

‘Setup / Valve’.

Note: It’s not possible to do ‘Valve and sensor

configuration‘ via remote operation.

3. Enable or disable ZERO function in menu

‘Setup / Sensor’.

4. Do 2 sensor configuration in menu

‘Setup / Sensor’.

3.6.3 ZERO

ZERO allows for the compensation of the sensor offset voltage.
When ZERO is performed the current value at the sensor input is equated to pressure zero. In case of a 2 sensor system
both sensor inputs will be adjusted. A max. offset voltage of +/-1.4V can be compensated. The offset value can be read
via local and remote operation.

Local operation

:

(‘Control View’, ‘Control Performance Analyzer’ or

‘Service Box 2‘)

Remote operation

:

(Refer to chapter «Digital inputs» for details)

1. Send

OPEN

VALVE

2. Wait until process chamber is evacuated and

sensor signal is not shifting anymore.

Go to menu ‘Zero / ZERO’ and follow instructions.

3. Send

ZERO

Note: Do not perform ZERO as long as pressure gauge voltage is shifting otherwise incorrect pressure reading is the
result. Refer to manual of sensor manufacturer for warm up time.

Note: Do not perform ZERO, if the base pressure of your vacuum system is higher than 1‰ of sensor full scale. We
recommend disabling ZERO function in this case; refer to «Valve configuration» of the setup procedure. Otherwise
incorrect pressure reading is the result.

«
...
18
19
20
21
22
...
»

Содержание Series 651






















































Отзывы:

Нет отзывов

Похожие инструкции для Series 651

Бренд: Falcon Страницы: 3

Бренд: Hardi Страницы: 2

Бренд: YASKAWA Страницы: 64

Бренд: V2 Страницы: 3

Бренд: S-COM Страницы: 400

Бренд: C.Nord Страницы: 100

CoreBuilder 9000

Бренд: 3Com Страницы: 78

REMOTE ACCESS SYSTEM 1500

Бренд: 3Com Страницы: 62

Бренд: Neets Страницы: 12

Бренд: National Instruments Страницы: 24

Бренд: Parker Страницы: 12

Бренд: TagMaster Страницы: 28

Бренд: ZPA Pecky, a.s. Страницы: 36

Бренд: Fox Страницы: 5

PetroVend PV200

Бренд: OPW Страницы: 2

Бренд: ACL Страницы: 20

Бренд: Alde Страницы: 36

YQPV-HP360V/100A

Бренд: PSC Solar Страницы: 22

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды