VAT Series 651 Скачать руководство пользователя | Manualshive

Страница: 10 / 53

background image

Installation, Operating & Maintenance Instructions

Series 651 DN 320-400 (I.D. 12“ - 16”), Logic

VAT Vakuumventile AG, CH-9469 Haag, Switzerland

Tel +41 81 771 61 61 Fax +41 81 771 48 30 [email protected] www.vatvalve.com

267736ED

2008-02-26

10/53

2.5 Requirements to sensor connection

To achieve fast and accurate pressure control a fast
sensor response is required.

Sensor response time: < 50ms

The sensor is normally connected to the chamber by a
pipe. To maintain that the response time is not degraded
by this connection it needs to meet the following
requirements:

Inner diameter of connection pipe:

> = 10 mm

Length of connection pipe:

< = 300 mm

These conductance guidelines must include all valves
and limiting orifices that may also be present.

Make also sure that there is no obstruction in front of
sensor connection port inside the chamber.

The sensor should also be mounted free of mechanical
shock and vibration.
Dynamic stray magnetic fields may introduce noise to
sensor output and should be avoided or shielded.

2.6 Electrical

connection

2.6.1 Sensor supply concepts

This valve offers 3 alternative concepts to supply the sensor(s) with power. This depends on the sensor type and valve
version that is used. This valve is available with an optional sensor power supply module (SPS) that converts

±

15 VDC

from the 24 VDC.

Concepts:

•

Ex 24 VDC supplied to POWER connector is feed through to SENSOR connector to supply 24 VDC
sensors. Refer to chapter «2.6.2 Power and sensor connection (+24 VDC sensors)» for schematic and correct
wiring.

•

External

±

15 VDC supplied to POWER connector is feed through to SENSOR connector to supply

±

15 VDC

sensors. Refer to chapter «2.6.3 Power and sensor connection (

±

15 VDC sensors) without optional SPS module»

for schematic and correct wiring.

•

Ex 24 VDC supplied to POWER connector is converted into

±

15 VDC by the valve internal SPS and

supplied to SENSOR connector to supply

±

15 VDC sensors. Refer to chapter «2.6.4 Power and sensor

connection (

±

15 VDC sensors) with optional SPS module» for schematic and correct wiring.

Valve versions:

•

651 . . - . . G . - . . . . / 651 . . - . . H . - . . . .

SPS module not included

•

651 . . - . . A . - . . . . / 651 . . - . . C . - . . . .

SPS module included

Note: The SPS module can be retrofitted. Refer to chapter «Retrofit / replacement procedure» for instruction.

«
...
8
9
10
11
12
...
»

Содержание Series 651






















































Отзывы:

Нет отзывов

Похожие инструкции для Series 651

Бренд: Samson Страницы: 52

Бренд: olympia electronics Страницы: 10

Бренд: Watts Страницы: 4

Бренд: WaterCop Страницы: 4

Бренд: ICP DAS USA Страницы: 8

Бренд: Paradox Страницы: 3

TruPortal TP-ADD-1DIP

Бренд: Interlogix Страницы: 9

Бренд: Dakota Digital Страницы: 12

653 - AE Series

Бренд: VAT Страницы: 103

Бренд: Festo Страницы: 87

Бренд: J+J Страницы: 56

Бренд: Generac Power Systems Страницы: 20

Бренд: Ravaglioli Страницы: 72

Бренд: Watts Industries Страницы: 20

PCI-to-IDE ATA-133

Бренд: Acard Страницы: 33

Бренд: YASKAWA Страницы: 35

I/O-SYSTEM 750-610

Бренд: WAGO Страницы: 14

Бренд: B meters Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды