VAT Series 651 Скачать руководство пользователя

Страница: 19 / 53

Installation, Operating & Maintenance Instructions

Series 651 DN 320-400 (I.D. 12“ - 16”), Logic

VAT Vakuumventile AG, CH-9469 Haag, Switzerland

Tel +41 81 771 61 61 Fax +41 81 771 48 30 [email protected] www.vatvalve.com

267736ED

2008-02-26

19/53

Errors:

Description

Digit 1

Digit 2

Digit 3

Digit 4

Compressed air failure
(< 4 bar / 55 psi)

A I

Compressed air on exhaust

A I

Fatal error occurred

Error code. Refer to «Trouble shooting» for details

3.6 Setup

procedure

To enable this valve for pressure control setup steps 1 to 5 must be performed.
In case position control is required only it’s sufficient to perform steps 1 and 2.

Setup step

Description

POWER UP

Turn on ex 24VDC power supply (and external

15 VDC for sensor power

supply if required). Refer to chapter «Behavior during power up» for details.

INTERFACE

CONFIGURATION

Refer to chapter «Interface configuration» for details.

VALVE

CONFIGURATION

Basic configurations of the valve must be adapted according to application needs.
Refer to chapter «Valve configuration» for details.

ZERO

Compensation of the sensor offset voltage.
Refer to chapter «ZERO» for details.

LEARN

Determination of the vacuum system characteristic to accommodate the PID
controller. Refer to chapter «LEARN» for details.

Note: Without LEARN the valve is not able to run pressure control

3.6.1 Interface

configuration

Interface configuration must be adapted according to application needs.

•

Functionality of digital inputs CLOSE VALVE and OPEN VALVE must be selected.

These may be configured as ‘not inverted‘ or ‘inverted‘. Default is ‘not inverted‘.

•

LEARN range configuration for remote operation must be selected.

This may either be ‘full range’ or pressure limit according of analog SETPOINT input. Default is ‘full range‘.

Local operation

(‘Control View’, ‘Control Performance Analyzer’ or

‘Service Box 2‘)

Remote operation

Do configuration in menu ‘Setup / Interface’.

Note: It’s not possible to do ‘Interface configuration‘

via remote operation.

Содержание Series 651






















































Результаты поиска

Содержание Series 651

Отзывы:

Похожие инструкции для Series 651

Бренды по названию

Популярные бренды

VAT Series 651, Инструкции по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание Series 651

Отзывы:

Похожие инструкции для Series 651

Бренды по названию

Популярные бренды