VAT Series 651 Скачать руководство пользователя | Manualshive

Страница: 17 / 53

background image

Installation, Operating & Maintenance Instructions

Series 651 DN 320-400 (I.D. 12“ - 16”), Logic

VAT Vakuumventile AG, CH-9469 Haag, Switzerland

Tel +41 81 771 61 61 Fax +41 81 771 48 30 [email protected] www.vatvalve.com

267736ED

2008-02-26

17/53

3.4 Behavior in case of power failure

Reaction of valve:

Valve position before
power failure:

Without Power Failure Option (PFO)

651 . . - . . G . - . . . .
651 . . - . . A  . - . . . .
651 . . - . . T  . - . . . .
651 . . - . . V  . - . . . .

With Power Failure Option (PFO)

651 . . - . . H . - . . . .
651 . . - . . C . - . . . .
651 . . - . . U . - . . . .
651 . . - . . W

. - . . . .

Closed (isolated)

Valve remains closed.

Valve open or in any intermediate
position

Sealing ring moves down and blocks the
pendulum plate at the current position.

Valve will close or open depending
on valve configuration *).
Default is not defined.

Display indicates F.

*) Provided that battery pack of the VAT controller is charged. Charging time after power up is 2 minutes max..

All parameters are stored in a power fail save memory.

3.5 Display

information

There is a 4 digit display located on the panel.
It displays configuration, status and position
information. For details refer to following
tables.

Display

1 2 3 4

«
...
15
16
17
18
19
...
»

Содержание Series 651






















































Отзывы:

Нет отзывов

Похожие инструкции для Series 651

Бренд: Ohsung Electronics Страницы: 18

Бренд: 1Control Страницы: 8

Бренд: Unipulse Страницы: 99

Бренд: Accutrol Страницы: 25

Бренд: Mainpine Страницы: 16

Бренд: Danfoss Страницы: 20

Бренд: Yudian Страницы: 26

Бренд: CAME Страницы: 18

Бренд: CAME Страницы: 28

Бренд: CAME Страницы: 28

Бренд: CAME Страницы: 4

Бренд: CAME Страницы: 40

Бренд: CAME Страницы: 26

Бренд: CAME Страницы: 34

Бренд: CAME Страницы: 2

Бренд: EasyIO Страницы: 18

Бренд: Easylift Страницы: 127

Бренд: H3C Страницы: 5

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды