VAT Series 651 Скачать руководство пользователя

Страница: 36 / 53

Installation, Operating & Maintenance Instructions

Series 651 DN 320-400 (I.D. 12“ - 16”), Logic

VAT Vakuumventile AG, CH-9469 Haag, Switzerland

Tel +41 81 771 61 61 Fax +41 81 771 48 30 [email protected] www.vatvalve.com

267736ED

2008-02-26

36/53

Failure

Check

Action

Sensor(s) connected?

Refer to «Electrical connection».

2 sensor version present at

valve controller?

Check valve version on page 1. Verify configuration. Refer

to «Setup procedure».

ZERO done?

Perform ZERO when base pressure is reached. Refer to

«ZERO» for details.

Pressure reading is wrong

pressure reading is negative

Does sensor power supply

provide enough power for
sensor(s)?

Verify sensor supply voltage.

Valve in open position, check

for O on display?

OPEN VALVE and bring chamber to base pressure before

performing ZERO.

ZERO does not work

ZERO disabled?

Enable ZERO.

Refer to «Valve and sensor configuration» for details.

Sensor voltage shifting?

Wait until sensor does not shift any more before

performing ZERO.

System pumped to base

pressure?

OPEN VALVE and bring chamber to base pressure before

performing ZERO.

Pressure is not ‘0’ after ZERO

Sensor offset voltage

exceeds ±1.4V

Replace

pressure gauge.

Safety mode active, check for

D on display?

Provide power to motor to allow for operation.

Refer to «Electrical connection» for details.

PRESSURE CONTROL

selected, check for P on
display?

Select PRESSURE CONTROL mode.

Refer to «Pressure control» for details.

PRESSURE CONTROL does
not work

LEARN done?

Perform LEARN.

Refer to «Setup procedure» for details.

Setup done completely?

Perform «Setup procedure» completely.

LEARN done?

Perform LEARN.

Refer to «LEARN» for details.

ZERO performed before

LEARN?

Perform ZERO then repeat LEARN.

Refer to «Setup procedure» for details.

LEARN interrupted?

Repeat LEARN.

Refer to «LEARN» for details.

Was gas flow stable during

LEARN?

Repeat LEARN with stable gas flow.

Refer to «LEARN» for details.

Tuning done?

Tune valve for application.

Refer to «Tuning of control performance» for details.

Is sensor range suited for

application?

Use a sensor with suitable range (controlled pressure

should be >3% and < 98% of sensor full scale).

PRESSURE CONTROL not
optimal

Noise on sensor signal?

Make sure a shielded sensor cable is used.

If you need any further information, please contact one of our service centers. You can find the addresses on our website:

http://www.vat.ch

Содержание Series 651






















































Результаты поиска

Содержание Series 651

Отзывы:

Похожие инструкции для Series 651

Бренды по названию

Популярные бренды

VAT Series 651, Инструкции по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание Series 651

Отзывы:

Похожие инструкции для Series 651

Бренды по названию

Популярные бренды