BendPak XpR-10AC-168 Скачать руководство пользователя страница 16

Страница: 16 / 76

StEP 6

(Mounting The OFFSIDE Column)

1. Position the OFFSIDE Column at the designated chalk

locations and secure to the floor following the same

procedures as outlined in STEP FIVE; Items 1-6.

StEP 7

(

Mounting the Top Trough Assembly)

1. Remove all of the Equalizer pulleys in preparation of

installing the Top Trough Assembly.

2. Using a lifting device, raise the Top Trough Assembly

into position on top of the Columns. Bolt to the columns

using the 10 mm Hex Bolts, Nuts and Washers.

you MuSt

POSITION THE SWITCH ENCLOSURE

ADjACENT POWERSIDE COLUMN. (See Fig. 7.1)

NotE:

In order to route the Equalizer Cables

the Pulleys must be removed.

WARNING !

If the anchor bolts were loosened to aid on the

installation of the Top Trough, tighten anchor bolts

as indicated in Step 5 items 4 - 6.

Fig 7.1

NotE:

To ease the installation of the Top Trough, it helps

to keep the anchor bolts loose on one of the

Columns until the Top Trough is Mounted.

Содержание XpR-10AC-168













































































Результаты поиска

Содержание XpR-10AC-168

Отзывы:

Похожие инструкции для XpR-10AC-168

Бренды по названию

Популярные бренды

BendPak XpR-10AC-168, Инструкция по установке и эксплуатации

Результаты поиска

Содержание XpR-10AC-168

Отзывы:

Похожие инструкции для XpR-10AC-168

Бренды по названию

Популярные бренды